Valve Assembly Used - U821
Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.
Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a new Coleman made valve assembly. Includes the valve, knob w/screw, fuel pick up tube and eccentric block. Fits both the 288 and 288A lanterns.
New feed tube assembly made by Coleman. Includes new Schrader valve and O-ring. Fits all 282, 285, 286, and 288 model lanterns.
This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.
Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.
This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
Valve for the 5154B, 5152D, and 5153A propane lanterns with electronic ignition. Comes with ignitor cam and knob/screw.
New old stock valve assembly for the QuickLite model 327 lantern.
Used valve assembly for the model 502 stove. Valve stem packing has not been changed but one will be included for you to change if needed.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.
Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.
P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
Used Valve Stem Assembly for the model 502 stove. Does not come with the valve wheel.
Comes with a new packing installed.
Used Sears valve assembly - has been cleaned and a new graphite packing has been installed.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel.
We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
A graphite valve stem packing is included with each of these in case you end up needing to change them.
This is a used valve assembly for a Canadian model 335 lantern.
Valve stem packing has not been changed but one will be included for you to change if needed.
NOS burner frame, Valve and Generator for the 158, 159 and 159X kerosene lamps. May fit others too. Very nice condition.
Burner assembly for the 158, 159 and 159X kerosene lamps. May fit others too. Valve operates well.
Can't tell if this is NOS or Used - Great Condition.