This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
New Generator for 201, 241 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 242K289, 201B5891 and 3000005402.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
New Generator for Model 237 Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Reproduction generator needle for the model 500 and for the 345 kerosene marine stove.
NOS valve assembly for the model 201 kerosene lantern.
Generator for the 639 Lantern. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005095.
Coleman Logo For Model 201 Kerosene Lantern
Coleman Logo For Model 214 Kerosene Lantern
Fits model 339 lantern. New generator includes new gas tip, spring, and tip cleaning wire.
Kerosene fuel tube for the 206 and 231 model lanterns
Solid brass nut for the model 345, 348, 500, & 502 stoves. Possibly used in other applications also. Refer to the parts diagram of your model if unsure.
Pre Heater Stem Assembly for the Marine Stove
Decal for some styles of the Canadian kerosene lanterns.
This is a reproduction generator for the very rare 238B lantern. These generators have been impossible to find for many years. Now you can get that rare 238B of yours running again. They were not cheap to get made but the workmanship is excellent. New generator includes new gas tip, spring, and tip cleaning wire.
Decal for the model 237B kerosene lantern
Pre-heater cup for the model 615 kerosene iron.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
The decal maker made a mistake on this run. Rather than the word kerosene being in black like it should be, he made it red. Kind of a cool decal for a custom lantern.
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.
NOS check valve for the 345 Kerosene stove, 348 Alcohol stove, the 5B radiant heater and some large kitchen range type appliances. This is larger than all the other Coleman check valves that are commonly used in lanterns and military applications. Width from side to side on top of the threads is 5/8".
For Coleman Double-Mantle Kerosene Lanterns like the 231 and 235. This may fit and work on a 206 also. Another name for this is the T44. It is the kerosene version of the 220E generator.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Reproduction Generator for the Model 249 Lantern. Generator includes gas tip, spring, and tip cleaning wire. Made in the USA.
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
New Reproduction Generator for Model 237 Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Pre Heater Stem Assembly for the Marine Stove
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
NOS maintenance kit for the 639 and 635B Lantern. Comes with a new generator, neoprene pump cup and push on nut.
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.
This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel.
We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
A graphite valve stem packing is included with each of these in case you end up needing to change them.
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
New Needle for the 237 generator. This is a reproduction part.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
