This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
Valve stem nut for the model 214, 242 and 200 series lanterns.
Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.
Reproduction generator nut for the 335 and 621 lanterns.
Reproduction generator nut for the 500 and 500A stove.
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
This is a used vent. It will fit models 220B through 220E.
Has paint chippings and a small bulge towards by the ball nut opening (see photos)
Lock Nut for the 200A lantern. Goes on the top end of the burner tube.
Solid brass nut for the model 345, 348, 500, & 502 stoves. Possibly used in other applications also. Refer to the parts diagram of your model if unsure.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Nut for 220H through K frame bottom.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
Globe nuts for the Thermos and Kamplite inverted lanterns.
Generator nut for Thermos lanterns.
Pack nut for the model 275 lantern.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Vent nut for the Northstar lantern.
Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.
This is a reproduction generator nut for the first Coleman lantern, the Arc lantern.
Parts kit for the model 5151A propane lantern. Includes heat shield, vent bracket, 2 gaskets and nut.
Reproduction generator for the Sunshine Safety lanterns and lamps. Similar to the Coleman Q99 but has a different nut. Will not work on Coleman lanterns and lamps.
Valve body for irons. The upright piece is 1 1/4 inches long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. The upright piece has a screen in the end of it. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Reproduction generator nut for the 252 military lantern. Made of brass.
Generator nut for the model 615 iron and the 5121 lantern.
Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
These came out of the old SMP factory. This is the washer that goes behind the pump nut on an SMP military lantern.
NOS generator nut for the model 500 and 500A stove.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
Used ball nut for the model 275 lantern. This is the checkered variety.
Unknown used ball nut. Kind of like half a ball nut.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
