Sears Valve Wheel Star, Used - E1623
Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.
Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a new Coleman made valve assembly. Includes the valve, knob w/screw, fuel pick up tube and eccentric block. Fits both the 288 and 288A lanterns.
This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.
This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.
For the model 520 stove. New generator includes new gas tip and tip cleaning wire. LINK for great info on these and what they fit.
Additional info: The 520 (aka M1941) and M1942 generators are usually interchangeable. The only exception is the early version of the M1942, known as the Mountaineer Stove. It has a vertical sprocket-type valve wheel. The generator on that stove seems to be unique in that it's a bit shorter than the later version.
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
N.O.S Valve stem for the model 335 and 339 lanterns.
Has a small chip on the valve wheel.
Valve for the 5154B, 5152D, and 5153A propane lanterns with electronic ignition. Comes with ignitor cam and knob/screw.
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.
This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
This is a new old stock pre-heater valve for the M2 military stove. Does not have the valve stem or wheel (knob).
Used maroon valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..
This is a reproduction knob for the Coleman made M1950 stove. The color of these match the original Coleman made color. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.