130 & 131 Lamp Valve, NOS - E1176
Lamp valve for 130G, 130K 130P and 131P. The bottom is threaded for a fuel and air tube to be attached.
Lamp valve for 130G, 130K 130P and 131P. The bottom is threaded for a fuel and air tube to be attached.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a few imperfections in the glass, color is faded and has one burn mark (see photos)
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
This is an original 220 Coleman vent. The black porcelain finish was custom done by Independence Porcelain Enamel (IPE). This is for the late 220F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Used filler cap with lanyard for the small backpacking lanterns - in very nice shape. Will also fit most other lantern and stoves that use the standard size filler cap. Comes with a new gasket that you will have to install.
Direction disk for the military lanterns. These came out of the old SMP factory.
Fits 285, 288, 290 and 295 model lanterns.
These are used and will vary in wear.
Reproduction filler plug for the old Quicklite lanterns and lamps. Made of solid brass. Now you can replace your old rounded off filler plug. Made to use the 427 gasket rather than the old lead gasket. Will come with the new gasket.
Reproduction lamp globe for the later style Coleman lamps. Real nice alternative to an expensive original. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Some people call this the 355 globe.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.
These made in the USA Mica Globes measure 4 1/2" x 3 1/2" and fit the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns.
Valve Assembly for the model 502 stove without fuel pickup tube.
This is the gasket only from the 5423A5611 small parts kit. OD 1/2", ID 3/16", Thickness is just under 1/16" Was commonly used on the model 5413, 5413A, 5423, 5430B, 5433, 5430B, 5430C, 5435C, 5435D and similar propane stoves.
I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.
Generator for some model of AGM lantern. Measures only 1 9/16 inches long.
This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.
Air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
New cotter pin for the 220B, 235 and other early style bails. This tiny cotter pin may be a little long and will have to be trimmed, but the width is correct to pass through the bail holes.
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
Block and Needle Assembly. Measures approximately 4 1/4 inches long.
This is a new production T-handle pump. It works great to pressurize your lantern, lamp, or Handy Gas Plant. Approximately 10 inches long.
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
From Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4″ long and fits nut sizes 11/16, 7/16, & 2, 5/16″ plus a 5/32″ slotted generator tip remover. This wrench also came with iron Models 4A & 609. Link is HERE.