Search

Fits model 275 lantern.

Pack nut for the model 275 lantern.

Fits 275A lantern.

Fits 275 or 275A lanterns. This is the flat one closest to the knob.

Fits 275 lantern.

Used burner assembly for the model 275 series lanterns.

Used frame for the model 275 and 275A lantern.

Used collar for a 275A. May show signs of wear.

This used block if for the 275A lantern. Not sure of compatibility with the 275. 

Air Intake Tube for the model 275 Lantern

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Used ball nut for the model 275 lantern. This is the checkered variety.

Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.

Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

Solid brass with stainless steel screen.

Same part number as 112-323

NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.

New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.

Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

Round steel burner cap for most models of double mantle lanterns and lamps.

Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.

Also known as 242B5381

This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.

C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.

This product is not included in the OCP free shipping program.

Photo's with lanterns are for illustration purposes only.

Replacement Decal/Logo for 275 Lantern - Red Chrome

E ring

New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Wear and finish will vary. 

Comes with a new gasket that you will have to install.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Fuel Cap with pressure gauge.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

This is a used one piece filler cap off the Model 200A burgundy. 

Comes with a new gasket that you will have to install.