1/4" Valve Stem Bushing - S137
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443 Instant Light, 2 & 3 Burner Stoves
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
Block and Needle Assembly. Measures approximately 4 1/4 inches long.
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.
This case is in good used shape. The two zippers work perfectly. Fabric is soft and does not feel old like some do after being around all these years. This fits all 425 model stoves (that is what is inside it in the photos).
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is a used one piece filler cap off the Model 200A burgundy.
Comes with a new gasket that you will have to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
Generator Coil. Rusty.
Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.
NOS Generator Coil.
Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.
Fits models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005106.
Fits model 426E, 413H, 432, 433 stoves. New generator includes new gas tip, spring, and tip cleaning wire. Same as part number 426-562C and 3000005104.