This fits models 200, 202, 200A,242, 242A, 242B, 242C, 247, 249. and 5101.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a few imperfections in the glass, color is faded and has one burn mark (see photos)
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Also known as part number R690B051.
These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Lock Nut for the 200A lantern. Goes on the top end of the burner tube.
New old stock Optimus Globe - Made in West Germany by Jenaer Suprax Glas. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 249 and other similar sized Lanterns.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a burn mark and one small spot missing the amber (see photos)
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.
Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.
New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
Used filler cap with lanyard for the small backpacking lanterns - in very nice shape. Will also fit most other lantern and stoves that use the standard size filler cap. Comes with a new gasket that you will have to install.
Mica globe for the small backpacking lanterns. Will fit models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Would be good for camping as it will not break like glass.
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
This is a used 242 Optimus Globe. It will fit models 200, 200A, 200B, 201, 202, 234, 242A, 242B, 242C, 243, 243A, 247 and 249.
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
Made by Coleman #51 Gold Top Mantles. 2 per pack. Fits Leisure Line Lanterns and most bayonet type lanterns Requires no tying or cutting of string Claims to be 4 times tougher than standard mantles
This is an original old red letter replacement logo globe made in USA. This globe will fit models 5107, 5151, and 5152. The globe is approximately 4 inches tall. The top diameter is 5 inches. The bottom diameter is 3 13/16 inches.
Valve Complete for the 5107 and 5107A propane Lantern
Compatible with 635 and the 621 series lanterns. This is a reproduction part.
Generator Needle For Northstar Lantern 2000-750T 2000-750 2000-750E 2000A750. This is a reproduction part.
Air intake tube for the model 5114 propane lantern.
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
This is a very nice reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns. Made of spring steel here in the USA.
Reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.
Used bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.
Bail for the Northstar propane lantern.
Used bail handle for the model 5107 lanterns
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Used ball nut for the model 275 lantern. This is the checkered variety.
Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.
Single Ball Nut. Fits all Coleman lanterns except the 242 type models.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
New burner cap for 621, 635 and 639 lanterns. Solid brass with stainless steel screen.
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Round steel burner cap for most models of double mantle lanterns and lamps.
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
This is a used burner frame for the model 200A lantern.
This is a used burner frame for the model 200A lantern.
