220 Filler Cap Insert, Used - E1222
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.
Compatible with 635 and the 621 series lanterns. This is a reproduction part.
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
New burner cap for 621, 635 and 639 lanterns. Solid brass with stainless steel screen.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is a used one piece filler cap off the Model 200A burgundy.
Comes with a new gasket that you will have to install.
Compatible with 635 and the 621 series lanterns. New generator includes new gas tip, spring, and tip cleaning wire. Coleman Canadian lantern generator G6 (635A297).
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
This globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C.
Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
NOS maintenance kit for the 639 and 635B Lantern. Comes with a new generator, neoprene pump cup and push on nut.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
These Peerless mantles are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.