These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.
New 200 burner frame Pal Nut is HERE.
New 200 burner frame Nut is HERE.
Lock Nut for the 200A lantern. Goes on the top end of the burner tube.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one is in very good condition.
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
These came out of the old SMP factory. This is the washer that goes behind the pump nut on an SMP military lantern.
Pack nut for the model 275 lantern.
Reproduction generator nut for the 500 and 500A stove.
Solid brass nut for the model 345, 348, 500, & 502 stoves. Possibly used in other applications also. Refer to the parts diagram of your model if unsure.
Small nut for bottom of stove grate.
This is a reproduction generator nut for the first Coleman lantern, the Arc lantern.
Unknown used ball nut. Kind of like half a ball nut.
Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.
They will all show varying signs of wear.
Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.
They will all show varying signs of wear/ wrench marks.
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
Used ball nut for the model 275 lantern. This is the checkered variety.
Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.
Single Ball Nut. Fits all Coleman lanterns except the 242 type models.
This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
From Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4″ long and fits nut sizes 11/16, 7/16, & 2, 5/16″ plus a 5/32″ slotted generator tip remover. This wrench also came with iron Models 4A & 609.  Link is HERE.
Unknown Coleman Heater Valves. Measures about 7 3/4" long from the tip to the nut.
Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.
this is an original used Finial for Lamps. This finial is missing the nut that threads onto the bottom.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
This is a new Coleman made generator for Model 290, 290A and 295 Lantern. Each includes new gas tip, spring, and cleaning needle.
This generator can be used on the 290 series lanterns, but you will have to use your original generator nut instead of the new one that comes with this generator. The 290 generators have been discontinued.
These are also known as part number 3000005404 and replaces the 290 & 290A part number of 290-5891.
Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859
Generator nut for the model 615 iron and the 5121 lantern.
NOS generator nut for the model 500 and 500A stove.
Reproduction generator nut for the 335 and 621 lanterns.
Used generator nut for the 335 and 621 lanterns.
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Reproduction generator nut for the 252 military lantern. Made of brass.
Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Generator W/O nut, for 450A700 stove
Used generator for the model 413E and 443 stoves according to early part diagrams.
I believe it is the same generator as part number 413A5621.
This is the earlier style with the square soldered on nut which does make it easier to install. Comes with tip needle, coil and housing. This one is in good shape.
Reproduction generator for the Sunshine Safety lanterns and lamps. Similar to the Coleman Q99 but has a different nut. Will not work on Coleman lanterns and lamps.
Globe nuts for the Thermos and Kamplite inverted lanterns.
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 5ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 3/16"
