Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear.
Vent rod for the model 5114 propane lantern.
Used vent for the model 275 and 275A. Has two chips - shown in photos.
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
Used maroon valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
Valve stem for iron. Stem measures 2 1/8" Long
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Used valve stem packing nut. Will also require a P01 graphite packing located HERE.
NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
Valve stem for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
T shirt shaped piece for the valve on slant lanterns and lamps.
Used valve body for the slant lanterns and lamps.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Used Valve Stem Assembly for the model 502 stove. Does not come with the valve wheel.
Comes with a new packing installed.
These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.
Unknown collar for a non Coleman lantern. Measures about 1 7/8 inches tall and has a diameter of 3 1/16 inches.
Tray. At widest point measures 11 7/8 X 7 3/4 inches.
Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.
This is a reproduction tip cleaner stem specifically for the #107 Leacock Kitchen Lamp. May fit other applications as well. It measures 2 1/8 inch long.
This is a service pack for cock 777 and pump assembly 2557
This is a new nozzle for the Tilley 606 vaporizer
Fuel tube and screen for Thermos stoves. It is 3 inches long.
Thermoelectric Cooler Switch
#11 mantles 2 pack For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles.
This is a used latch that was used on many stoves. Known to fit 413G. It may fit others.
This is a used latch that was used on many stoves. Known to fit 413G. It may fit others.
This is a used stove handle for many stoves.
It measures 5 13/16 inches across. Will show signs of rust and wear.
It is know for sure to fit the 413E and a 425C.
Vinyl adhesive-backed stencil for Model 2 stove. Stick it on your tank, paint, then remove.
Zippo brand Flints for the Coleman Lantern Spark Igniter.
Used top half of the burner assembly for a slant lantern or lamp.
Shade holder screw for the model 117, 118, and 119 lamp. Looks like the more common shade holder screw but has much larger threads. Will not fit other models.
Used shade holder for the old 117, 118 and 119 lamps. All vary in wear and condition.
Used Sears small hat ventilator. Will also work on the model 220 lantern. This one has some paint chipping and a dent (see photos)
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.
Need more information on the valve core? Click HERE.
Radiant heater direction disk.
Amish style filler plug for the early Quick-Lite lanterns and lamps. Does not use an air stem and requires a hand pump.
Reproduction Q99 generator for the old Quicklite style lanterns and lamps. They work great.
Interchangeable with the Q99 or R55 generator. Fits the model 327, 427 and Slant 220 lanterns. NOS - This does not come in original packaging and they are rusty on the outside. They are made of steel.
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
