Wrench 220B - R300
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear.
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
Used valve stem for the model 220/228H, J, and K lanterns. Has been cleaned and will have new graphite packing.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.
Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns.
Will all vary in wear and some may have rust .
Same as part number 288-1251
New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.
Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.
Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295.
Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.
This product is not included in the OCP free shipping program.
Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
Interchangeable with the Q99 or R55 generator. Fits the model 327, 427 and Slant 220 lanterns. NOS - This does not come in original packaging and they are rusty on the outside. They are made of steel.
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.