Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
For the model 520 stove. New generator includes new gas tip and tip cleaning wire. LINK for great info on these and what they fit.
Additional info: The 520 (aka M1941) and M1942 generators are usually interchangeable. The only exception is the early version of the M1942, known as the Mountaineer Stove. It has a vertical sprocket-type valve wheel. The generator on that stove seems to be unique in that it's a bit shorter than the later version.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Used valve stem nut for many Coleman lanterns.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.
This is a used pump square nut.
Comes with one square nut ONLY.
Used Pump Assembly Spring
Spring ONLY
Stem (lighter) assembly. This was the last style used on the 500B Canadian Stove, will also work on the 500 and 500A. This is a rare part.
Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.
1/4 inch long screw for the 500 stove. Used on the baffle, see description tab for more details. Two are required for the 500 stove.
Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.
Pump plunger for the model 505. Also fits the 222 series lanterns.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Large leather pump cup for the T-Handle pumps, kitchen ranges, and other larger appliances. The flat portion of the cup measures 1" wide. For pump barrels with a 1 1/4 inch diameter.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
These Peerless mantles are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.
Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.
Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.
O-Ring sizes are #6, #7, and #9, made of Flourosilicone.
We know it does work on these models: 533, 440, 442
Does not work on the 400B, 508B, 533A, 3024
This is a used old copper funnel. Smaller spout end fits the model 242 series lanterns and 500 stoves well.
Reproduction needle for the 530 vaporizer. Will also work on the M1950 vaporizer.
This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.
Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.
NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit. No other sizes of chain are currently available that are an exact match to what was used.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
"Butterfly" mantle No 41. 500-600 C.P. Suitable for 500 candlepower lanterns such as model 236 and 237. 1 mantle per pack.
This is the spring used in the non return valve located in the bottom of the pump. Reproduction part.
This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.
This is a cap for the end of the M1950 pump. This screws into the bottom of the pump.
This is a used pip holder cup for the M1950 stove pump. Comes with a new rubber pip.
Used combo pre-heater cup and gen nut for the M1950 stove.
Original reproduction wrench for the model 536 or M1950 stove.
Used carry case for the M1950 stove. Can also be used for other military stoves such as the 520. Will not fit the 530. Has a couple dents and scratches (see photos)
This is a reproduction knob for the Rogers made M1950 stove. The color of these match the original Rogers darker color. We have found the earlier stoves (made around 1953) were darker than the newer ones (made around 1963). The last photo shows the difference in color between the two. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.
This is a reproduction knob for the Coleman made M1950 stove. The color of these match the original Coleman made color. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.
Fuel tube gasket for the model M1950 military stove.
New Old Stock M1950 burner frame.
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These will not fit the 530 stove without using a 1950 generator and a 530 needle.
Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.
This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.
Decal for the Preway made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
This is the spring used in the non return valve located in the bottom of the M1942 pump. Reproduction part.
Decal for the Coleman made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
Decal for the Aladdin made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
