- May 1, 2024Gather 'round, fellow GPA enthusiasts!Our annual convention is fast approaching, and guess what? It’s practically in our backyard—just 40 miles from our OCP home! June 27 to 29, 2024
Search
260 products found
Sort by:Name Z - A
Vent bracket - E1317
Vent bracket.
Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern.
Vent Bracket, Used - E1021
Used Vent bracket.
Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern.
Valve Wheel Screw - S77
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Valve Wheel Screw - S60
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
- New!
U Tube Newer Style With Venturi Used - E1486
This is a used newer style U tube with Venturi. These are used.
Tip Cleaner Stem Reproduction - R651
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.
Tip Cleaner Stem Packing - S129
These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.
String Tie #11 Mantle - M07
#11 mantles 2 pack For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles.
Spring Clip (Preheater Cup) - R579
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
- New!
Snuffer Cap Used - E1447
Only 1 left in stockThis is a used snuffer cap.. Will fit only the 513 and 513K heaters.
Small valve stem packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - P02
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Small valve stem packing - P02
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Slip-On #51 Mantles - M10
Coleman #51 Mantles. 2 per pack Fits models 3018, 3023, 3112, 5130, 5132, 5133, 5134, 5136, and 9742
Also known as part number 2000026608.
Short Pump Plunger, Plastic Cap - C037
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
Shade Holder Rod With Nut - S132
Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.
Schrader Valve Core - R510
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.Need more information on the valve core? Click HERE.
Reproduction Gas Tip - GT2
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Reproduction 226 Generator - R205
Reproduction Generator for Model 226A700 and the 226-700. Generator includes new gas tip, spring, and tip cleaning wire.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend the 226 generator as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
Regulator Valve Assembly, NOS - E1260
Valve for the 5154B, 5152D, and 5153A propane lanterns with electronic ignition. Comes with ignitor cam and knob/screw.
Red Knob - S172
This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.Pump Northstar - C044
Brand new pump For the Northstar Lantern.
Fits models 2000-750T, 2000-750, 2000-750E, and 2000A750.
Pump Cup, Neoprene - C019
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Pump Cup Assembly - S38
New reproduction pump cup assembly for 242 NL (No Letter), 242A , 242K, 243 , 246 and or any Coleman lantern or stove from the early 30's with a solid pump stem with no air hole in the middle. These are made for the USA manufactured Coleman pump shafts and will fit as they should. If yours is made in Canada, you will have to use a small file to widen the brass center to a cone shape to match your pump shaft - see the photos. Also known as part number 233-518
Pump Cup & Nut, Neoprene - C008
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091- Free Shipping
Pump Clip, Used - S100
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
- Free Shipping
Pump Assy Leather Used Push On Nut - U811
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Pump Assembly, Universal - C045
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
Pump Assembly, Universal - C006
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.Pump Assembly, 220C Thick Steel Cap, Used - E1296
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
Pump Assembly Plastic Cap, Used - E1426
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Pump Assembly Neoprene Used - E1561
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Pump Assembly Neoprene Fixed End, Used - E1420
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.