Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
For the model 520 stove. New generator includes new gas tip and tip cleaning wire. LINK for great info on these and what they fit.
Additional info: The 520 (aka M1941) and M1942 generators are usually interchangeable. The only exception is the early version of the M1942, known as the Mountaineer Stove. It has a vertical sprocket-type valve wheel. The generator on that stove seems to be unique in that it's a bit shorter than the later version.
Large Military generator. New generator includes new gas tip, spring, and tip cleaning wire. Does not fit the 520, 523 or 530. Much bigger.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.
Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.
This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.
Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.
NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit. No other sizes of chain are currently available that are an exact match to what was used.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Master Inlet Control Valve
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Very little pump only for the model 615 irons with the built in pump.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
This is a 10 PACK of gaskets for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
