Wrench 220B - R300
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear.
Brass Vent Bolt for 243B, and all 241 Lanterns - this bolts down into the top of the frame to hold the vent.
Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.
Unknown screen. Measures 1/2 inch in diameter. Very fine brass. Seems too fine to be for a burner screen. Came out of a lot of old AGM parts.
Don't know what this came from. It is about 4 7/8" long, the smallest end is about 3/4" wide and the biggest end is about 7/8" wide. From wing to wing it is about 2 1/2" wide.
Term-Sport Alcohol Stove Gasket Set. These gaskets are for the filler cap and the burner tube. Both are made from fuel resistant materials that will last for years (ECH - Cap & Viton - Burner Tube).
Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.
Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.
This is a service pack for burner 1222 - R1A and R55 heaters
New old stock stove tank for the 3 burner Thermos stove models 8431 and 8432.
Used burner assembly for the Thermos 2 mantle lantern. In good shape.
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
Burner support screw for a 502 stove. Each stove requires 3 total.
NOS Military Lantern globe channel. Crimps on burner frame to hold quadrant globe panes.
Pre-heater generator for the Urn Burner 404, 505, 707; Water heater 1; Handy Gas Plant 5052; Pre-heater 544-383.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
New nickel plated brass burner caps with round head. Fits most models of double mantle lantern and lamps.
N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These will not fit the 530 stove without using a 1950 generator and a 530 needle.
NOS burner frame, Valve and Generator for the 158, 159 and 159X kerosene lamps. May fit others too. Very nice condition.
NOS Burner Cap for the early stove models 2, 9, 2C, 9C, 2E, 9E, 2F, and 9F
Cannot be used on the Model 1.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
This is a reproduction burner ball for the Focus 5 heater. Has been field tested and works excellent. Comes with instructions on how to remove the screen from your old ball and install the new - see those instructions in the "Description" area below. Made of stainless steel. The smaller inner screen would need to be good on your current burner for it to work correctly. Made in the USA.
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
Burner tube for the Canadian model 200 lantern. It is 1 5/8 inches long which is a little shorter than the US 200A burner tube.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.