This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.
Valve assembly for the 152 lamp. It also might be for a 132 lamp. I believe I have identified this part correctly but am not 100% sure. It has threads on the outside of the valve bottom so it would screw into rather than on the lamp. It also has threads for a fuel and air tube to be screwed into the bottom. It would take a 220 size generator body. When looking at the valve wheel, the tip cleaner mechanism would be on the left and the air tube would be in the back.
Valve assembly for the 152 lamp. It also might be for a 132 lamp. I believe I have identified this part correctly but am not 100% sure. It has threads on the outside of the valve bottom so it would screw into rather than on the lamp. It also has threads for a fuel and air tube to be screwed into the bottom. It would take a 220 size generator body. When looking at the valve wheel, the tip cleaner mechanism would be on the left and the air tube would be in the back.
Unknown fuel tube. Pretty sure they are for Thermos.
Unknown fuel tube. Measures approx 2 3/8"
Unknown fuel tube possibly for a stove. Measures 5 3/4" long.
Don't know if it is used or NOS.
Unknown fuel tube. Measures 2 13/16 inches long.
Term-Sport Alcohol Stove Gasket Set. These gaskets are for the filler cap and the burner tube. Both are made from fuel resistant materials that will last for years (ECH - Cap & Viton - Burner Tube).
Fuel tube screen for Thermos and some AGM stoves. Also know by AGM part number 42-833.
Fuel tube and screen for Thermos stoves. It is 3 inches long.
Fuel tube and screen for Thermos products. It is 3 7/8 inches long.
Fuel tube and screen for Thermos appliances. It is 2 5/8 inches long.
Fuel tube and screen for Thermos stoves. It is 2 1/2 inches long.
This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.
Fuel tube gasket for the model M1950 military stove.
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.
Fuel and Air Tube for many stoves. Same as part number 425-6461.
Fits 2G, 2H, 4F, 6B, 6F, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 417B, 425 models, 500, &500A.
NOS fuel tube for the slant 220 and 228 lanterns.
New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".
Reproduction fuel tube for the Model 457, 460 and 575 Handy Gas Plant. Also fits stove models 375, 375A, and 376.
Kerosene fuel tube for the 206 and 231 model lanterns
Fuel tube. Measures 3 1/8 inches long.
Fuel tip used on the end of the fuel tubes of early 220/228B lanterns, 236 and some lamps.
Reproduction shorter fuel and air tube for the double mantle Sears lanterns made by Coleman.
N.O.S fuel and air tube for lamps.
Fuel Air Tube for the 413 series and 442 series 2 burner stoves. NOS.
New feed tube assembly made by Coleman. Includes new Schrader valve and O-ring. Fits all 282, 285, 286, and 288 model lanterns.
This is a new Coleman made valve assembly. Includes the valve, knob w/screw, fuel pick up tube and eccentric block. Fits both the 288 and 288A lanterns.
Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
Lamp valve for 130G, 130K 130P and 131P. The bottom is threaded for a fuel and air tube to be attached.
