Valve Wheel Screw, Used - S103
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.
This is a service pack for burner 1222 - R1A and R55 heaters
This is a service pack for cock 777 and pump assembly 2557
This is a used snuffer cap.. Will fit only the 513 and 513K heaters.
Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".
Reproduction cast aluminum pre-heater cup for the rare 242K lantern. Most of the 242K lanterns are missing the original pre-heater cup. If you are a purist and want to complete your 242K project then you will be very pleased with this. Looks identical to the original.
Original used pre-heater cup for the model 234 lantern. Also would be correct for the Canadian model 247 lantern.
Pre-heater cup for the model 237 lantern. This is a new production cup made out of brass. It is very high quality and fits the 237 nice and snug. Will also fit a 530 stove if you want to install a PH cup on it.
Pre-heater generator for the Urn Burner 404, 505, 707; Water heater 1; Handy Gas Plant 5052; Pre-heater 544-383.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
This is a gasket sealer that many use for sealing valves to tanks. Is flexible when dry and offers good fuel resistance.
O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400A.
Two required for the model 550 stove.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
This is a new old stock pre-heater valve for the M2 military stove. Does not have the valve stem or wheel (knob).
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
This is a new production stainless steel element for the Coleman Hot Ray heaters. Replaces the old ceramic radiant that is usually broken or missing.
Used and rusty heater box for the Hot Beam #3 heater. See photos for condition.