Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Vent nut for the Northstar lantern.
This is a used vent. It will fit models 220B through 220E.
Has paint chippings and a small bulge towards by the ball nut opening (see photos)
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
Reproduction brass 335 valve stem nut
Used valve stem packing nut. Will also require a P01 graphite packing located HERE.
Used valve stem nut for many Coleman lanterns.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Valve body for irons. The upright piece is 1 1/4 inches long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. The upright piece has a screen in the end of it. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.
P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).
This is a used pump square nut.
Comes with one square nut ONLY.
Don't know the part number for this valve and generator. It measures 10 1/4 inches long from tip to end of nut.
Generator nut for Thermos lanterns.
This is a reproduction generator, old style with the square nut. Each includes new gas tip, spring, and tip cleaning wire. This will fit models: 425, 425B, 425C, 425D, 425E, 425F, Sears 476.72301, 476.72244 & 476.74960.
Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Parts kit for the model 5151A propane lantern. Includes heat shield, vent bracket, 2 gaskets and nut.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Valve stem nut for the model 214, 242 and 200 series lanterns.
Nut for 220H through K frame bottom.
Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.
Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.
Used wing nut for the milspec lantern.
NOS maintenance kit for the 639 and 635B Lantern. Comes with a new generator, neoprene pump cup and push on nut.
Used combo pre-heater cup and gen nut for the M1950 stove.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 1/8"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 1/8"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 5ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
Globe nuts for the Thermos and Kamplite inverted lanterns.
