Spring for the inside of the 236 generator.
This is a new reproduction 236 generator. New generator includes new gas tip, spring, and tip cleaning wire.
Eccentric block for the model 236 and 5121 lanterns.
Reproduction generator needle for the model 236 lantern.
This is a very nice reproduction bail handle for the model 236 and 237 lanterns. Made of spring steel here in the USA.
This is a reproduction bail handle for the model 236 and 237 lanterns.
They are new but a little rusty and warped/bent - they can be fixed with a little patience and a propane torch.
Brass burner tube for the models 236 and 237.
Reproduction vent rod for the model 236 and 237 lantern. Made of solid brass.
New burner cap & screen for the model 236, 237 and 249 lanterns.
Solid brass with stainless steel screen.
New burner screen for the models 236, 237 and 249.
"Butterfly" mantle No 41. 500-600 C.P. Suitable for 500 candlepower lanterns such as model 236 and 237. 1 mantle per pack.
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
Fuel tip used on the end of the fuel tubes of early 220/228B lanterns, 236 and some lamps.
This globe will fit models 236, 237, 237A, 237B 635, 639, 639A, 639B, and 639C.
#11 mantles 2 pack For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles.
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.
Dark Red Border Logo with "Reg.", & "Lantern". For "Some" 1971 to 1983 200A, 220, 228, 335, 236A, 237A Lanterns. This and the D11 were used interchangeably on the same lanterns/stoves. Compare with your original.
These Peerless mantles are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the double screw holes on the plunger cap.
Used steel pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. Has the double screw holes on the plunger cap.
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the single screw hole on the plunger cap.
For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.
These made in the USA Mica Globes measure 4 7/8" x 5 1/4" and fit 206, 220, 228, 231, 236, 237, 290, 295, and QuickLite lanterns.
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.
New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
Used cardboard tube that goes inside of the 200A and 220 size generators, and many others.Â
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
Zippo brand Flints for the Coleman Lantern Spark Igniter.
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
Single Ball Nut. Fits all Coleman lanterns except the 242 type models.
New Coleman made Spark Igniter. Comes in new packaging with instructions.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used Pump Assembly Spring
Spring ONLY
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
This is a used pump square nut.
Comes with one square nut ONLY.
NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
