Pump Assembly Neoprene Fixed End, Used - E1420
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
Direction disk for the military lanterns. These came out of the old SMP factory.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.
This is a used burner assembly with the round mixing chamber that will fit the model 220F & 228F. It will be in fine working condition. It may show signs of tarnish and other spots from being old.
Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns.
Will all vary in wear and some may have rust .
Same as part number 288-1251
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
This is a very nice reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns. Made of spring steel here in the USA.
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".
Used short style vent for the 200/200A lanterns made in 1963 and after.
This vent has some scratches/scuffs and paint chippings (shown in photos)
Reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.
Reproduction generator for the AGM model LRL21, LRL21A, LRL22, KL2, and JC Higgins model 710.7400, 710.74001 lanterns. Part number on JC Higgins parts diagram is 7110 - Generator Assembly
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.
New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.