200A Optimus Globe - G121
New old stock Optimus Globe - Made in West Germany by Jenaer Suprax Glas. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 249 and other similar sized Lanterns.
New old stock Optimus Globe - Made in West Germany by Jenaer Suprax Glas. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 249 and other similar sized Lanterns.
This is a used 242 Optimus Globe. It will fit models 200, 200A, 200B, 201, 202, 234, 242A, 242B, 242C, 243, 243A, 247 and 249.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a burn mark and one small spot missing the amber (see photos)
Yellow Border Logo Used on Coleman 200A Lanterns 1952 - 1953
Yellow Border Logo Used on Coleman 200A Lanterns 1954 to 1960 "Reg."
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.
This is a used unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is a Fred Kuntz reproduction. Glass measures 3 1/2" Wide X 4" Tall.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Reproduction Generator for 200, 200A, 202, 242, 243, 243A & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire. The generator is complete and you need nothing else for the install.
Same as the old part numbers T66, 200A2891 and 3000005089.
Burner tube for the Canadian model 200 lantern. It is 1 5/8 inches long which is a little shorter than the US 200A burner tube.
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Looks like it may have gotten a little too hot and burned (see photos)
These came out of the old SMP factory. New pump rod for the military lantern. Would also work on a 220/228B or C. Also would work on the stoves that took a longer pump such as the model 415.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
The decal maker made a mistake on this run. Rather than the word kerosene being in black like it should be, he made it red. Kind of a cool decal for a custom lantern.
This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
For Coleman Double-Mantle Kerosene Lanterns like the 231 and 235. This may fit and work on a 206 also. Another name for this is the T44. It is the kerosene version of the 220E generator.
New Generator for 201, 241 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 242K289, 201B5891 and 3000005402.
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
Coleman Decal For some Canadian Made Lanterns. Decal measures approximately 2 1/2 inches long and is one inch tall. This matches the earliest vinyl style of the decal on a few of the 200 Canadian lanterns made around 1955
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
Valve stem for Quick-Lite lanterns.
These have not been serviced or cleaned and may need a new P02 packing which is HERE.
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.
Need more information on the valve core? Click HERE.
Used valve stem for Quick-Lite lanterns.
These have not been serviced or cleaned and may need a new P02 packing which is HERE.
From Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4″ long and fits nut sizes 11/16, 7/16, & 2, 5/16″ plus a 5/32″ slotted generator tip remover. This wrench also came with iron Models 4A & 609.  Link is HERE.
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
Air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.
It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417.
It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This original globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417. Made in the USA. This globe is used.
Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
Amber globe for the 288 size lantern. Has no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
Picket amber globe for the 288 size lantern. Has no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
This is a new Coleman made generator for lantern models 200B, 286 & 288. Generator includes new gas tip, spring, and tip cleaning wire.
This part is also known as part number 3000005403.
Used gas tip for the Q99 generator and some Quick-Lite Lanterns and Lamps. Very tarnished
Used burner assembly for the old model 327,427, also for CQ and Air O Lite lanterns. Will also work on other lamps that would have originally taken the Q99 generator.
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
Also known as part numbers 2000038026 & R214D046C.
This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.
Steel air intake tube for the old Quicklite lanterns and CQ lamps.
Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
Reproduction Q99 generator for the old Quicklite style lanterns and lamps. They work great.