- New!
200 Generator Body, Used - E1050
Used generator body only. This is only the brass tube of the generator and the gas tip. May or may not have the internal spring and packing tube. No needle is with this.
Used generator body only. This is only the brass tube of the generator and the gas tip. May or may not have the internal spring and packing tube. No needle is with this.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
This is a used fount for the model 242 Lantern. It is date stamped 4-47. Has some paint chipping and a couple very small dents. The sunshine logo looks faded but is there.
It will work for models 242, 242A, 242B, 242C, 243, 243A, 247, and 242K.
This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)
Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Will come with a new gasket for you to install if needed.
This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Comes with a new gasket for you to installed if needed.
These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a burn mark and one small spot missing the amber (see photos)
These mica panels are 3" x 5" in size.
General information:
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a few imperfections in the glass, color is faded and has one burn mark (see photos)
This is a used unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is a Fred Kuntz reproduction. Glass measures 3 1/2" Wide X 4" Tall.
New old stock Optimus Globe - Made in West Germany by Jenaer Suprax Glas. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 249 and other similar sized Lanterns.
This is a used 242 Optimus Globe. It will fit models 200, 200A, 200B, 201, 202, 234, 242A, 242B, 242C, 243, 243A, 247 and 249.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
Reproduction needle assembly for the 200A2891 T66 generator used on models 121, 200, 200A, 202, 242, 242B, 242C, 476.72211, 476.74550
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
Reproduction generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns.
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Also known as part number R690B051.
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Used generator spring for 200, 200A, 220, 228, 242, 243, 202 & Similar Sears Lanterns. This is the older style.
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the double screw holes on the plunger cap.
Used steel pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. Has the double screw holes on the plunger cap.
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the single screw hole on the plunger cap.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a used bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Will show wear and rust and such, but be solid.
Reproduction Generator for 200, 200A, 202, 242, 243, 243A & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire. The generator is complete and you need nothing else for the install.
Same as the old part numbers T66, 200A2891 and 3000005089.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.
Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.
This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Looks identical to the original.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.
This is a 10 PACK of gaskets for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.