Search

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Used valve wheel screw.  Will be in good condition.

Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

New 200 burner frame Pal Nut is HERE.

New 200 burner frame Nut is HERE.

NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.

Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.

Pump Clip

Push on nut for pump. The large push on nut is used with the neoprene pump cup.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Coleman Logo For Model 201 Kerosene Lantern

The decal maker made a mistake on this run. Rather than the word kerosene being in black like it should be, he made it red. Kind of a cool decal for a custom lantern.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. 

These simply slide on and you cross the wires instead of tying strings - very quick to install.

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

These are NOS Coleman ball nuts

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

These are reproduction brass ball nuts. This is the common sized ball nut used on most Coleman lanterns.

Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Coleman's Most Popular Sized Mantles. 2 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004345.

Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111

Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.

Solid brass with stainless steel screen.

These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.

Single Ball Nut. Fits all Coleman lanterns except the 242 type models.

NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.

Also known as part number 3000005094.

Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.

New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.

Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.

Lock Nut for the 200A lantern. Goes on the top end of the burner tube.

This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242  and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.

Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.

This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.

Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.

Used gas tip for 201-5891 generator.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.

Coleman's Most Popular Sized Mantles. 4 mantles per pack. 

Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960

Also known as part number 3000004344.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.