These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a few imperfections in the glass, color is faded and has one burn mark (see photos)
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.
This is a used Pyrex old red letter logo replacement globe used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
This fits models 200, 202, 200A,242, 242A, 242B, 242C, 247, 249. and 5101.
This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)
This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
This is a used old copper funnel. Smaller spout end fits the model 242 series lanterns and 500 stoves well.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a used fount for the model 242 Lantern. It is date stamped 4-47. Has some paint chipping and a couple very small dents. The sunshine logo looks faded but is there.
It will work for models 242, 242A, 242B, 242C, 243, 243A, 247, and 242K.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
New Old Stock parts. Comes with original box.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Comes with a new gasket for you to installed if needed.
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Rebuild kit for models 242, 242A, 242B, and the 242C lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
This is a used unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is a Fred Kuntz reproduction. Glass measures 3 1/2" Wide X 4" Tall.
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the double screw holes on the plunger cap.
Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Will come with a new gasket for you to install if needed.
Used steel pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. Has the double screw holes on the plunger cap.
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the single screw hole on the plunger cap.
This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
This one will need a new burner cap or screen.
Is marked with 3000.
This is a used Burner frame for the 242A through C lantern. Will also work on the 247.
Is stamped with 3000.
These mica panels are 3" x 5" in size.
General information:
New Generator for 201, 241 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 242K289, 201B5891 and 3000005402.
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
Is stamped with 3000.
This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
Brass Pin for 242 or 242NL Lantern - will not fit other versions of the 242. This is secured directly to the 242 vent. This fits into the burner frame hole - It forms to the 242 vent and captures it permanently after you heat it and swedge it in place. See directions below. Comes with Steel rod to assist in the process.
Installing Pin into a 242 vent:
You will notice the edges of the lip will fall away.
Reproduction check valve for 242, 242A, 242K, 243 and 243A lanterns. This is the re-buildable type check valve for early single mantle lanterns that did not use an air stem. Will not work with others.
This is a used steel collar for the model 242C lantern. Will vary in amount of rust and wear.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
This is a used collar for the model 242B lantern. It may have spots of rust or other discoloration/ stains.
This is a used collar for the model 242C lantern. All will vary with wear and discoloration.
This is a used collar for the model 242B "Sport-Lite" lantern. It may have spots of rust or other discoloration/ stains.
Reproduction Generator for 200, 200A, 202, 242, 243, 243A & Similar Sears Lanterns. New generator includes new gas tip, spring, and tip cleaning wire. The generator is complete and you need nothing else for the install.
Same as the old part numbers T66, 200A2891 and 3000005089.
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Also known as part number R690B051.
This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
Used Canadian 242B collar with small writing.
Each will vary in amount of wear and discoloration.
New reproduction pump cup assembly for 242 NL (No Letter), 242A , 242K, 243 , 246 and or any Coleman lantern or stove from the early 30's with a solid pump stem with no air hole in the middle. These are made for the USA manufactured Coleman pump shafts and will fit as they should. If yours is made in Canada, you will have to use a small file to widen the brass center to a cone shape to match your pump shaft - see the photos. Also known as part number 233-518
New Coleman made Spark Igniter. Comes in new packaging with instructions.
Reproduction cast aluminum pre-heater cup for the rare 242K lantern. Most of the 242K lanterns are missing the original pre-heater cup. If you are a purist and want to complete your 242K project then you will be very pleased with this. Looks identical to the original.
This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.
Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.
They will all show varying signs of wear.
This is a used steel collar for the model 242C lantern. Has a good amount of rust.
