Search

200A Burner Tube

This is a used collar for the model 200A lantern. 

It may show signs of wear/scratches. Each collar may slightly vary in wear.

This fits models 200, 202, 200A,242, 242A, 242B, 242C, 247, 249. and 5101.

Lock Nut for the 200A lantern. Goes on the top end of the burner tube.

New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

Also known as part number R690B051.

Used Direction disk for the single mantle 200A lantern.

This is a new gasket for your metal snap on parts safe. Fits the 200A size metal safe. Measures 5 1/4" from outside edge to outside edge of gasket.

These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.

This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.

Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.

These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.

Has a few imperfections in the glass, color is faded and has one burn mark (see photos)

Used short style vent for the 200/200A lanterns made in 1963 and after.

This vent has some scratches/scuffs and paint chippings (shown in photos) 

Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.

This is a used Pyrex old red letter logo replacement globe used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.

New NOS valve stem for the model 200A lantern.

Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw. 

This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.

Fits 1961 200A Lanterns - Yellow Border Logo

Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.

New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.

This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.

Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.

Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.

Includes:

• 4 Coleman string tie mantles for the 200 or 200A lantern
• 1 Reproduction Generator for the 200 or 200A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 200 HERE
• 200A HERE

Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 200 or 200A lantern
• 1 Reproduction Generator for the 200 or 200A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 200 HERE
• 200A HERE

Yellow Border Logo Used on Coleman 200A Lanterns 1952 - 1953

Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw. 

This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.

Yellow Border Logo Used on Coleman 200A Lanterns 1954 to 1960 "Reg."

White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965  to 1971 200A, 220 & 228 F Lanterns. Also fits the 220G, 

Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns

No Border Logo with "Reg." & "Lantern" for 1961  to 1964 200A, 220 & 228 E & F Lanterns

White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.

Decal for the early Coleman LP lantern.

Decal for the early Coleman LP lantern.

Dark Red Border Logo with "Reg.", & "Lantern". For "Some" 1971 to 1983 200A, 220, 228, 335, 236A, 237A Lanterns. This and the D11 were used interchangeably on the same lanterns/stoves. Compare with your original.

OCP Collector's Edition 200A Coffee Mug - 11oz.

This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.

Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Reproduction U tube and venturi for the model 200A lantern.

Used generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns. This is the older style.

Reproduction generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns.

This is a used tall style vent for the 200 and 200A Lantern. 

Has some paint chips (see photos)

Reproduction stainless steel bail handle for the models 202, 200, and 200A.

This is a used burner frame for the model 200A lantern. 

This is a used burner frame for the model 200A lantern.

Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)

This is a used fount for the 200A lantern dated 9-60. Has some scratches/paint chipping and a dent by the pump assembly (see photos)

This is a used fount for the model 200A lantern. Has some paint chipping, scratches/scuffs and two very small dents you can only see in certain lights (see photos). Otherwise in nice shape - inside of tank looks good too.

Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)

Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).