This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
Most Popular Sized Mantles. 4 mantles per pack. Use on these lanterns models: 200, 200A 201, 214, 220, 228, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960. Also all Coleman Lamps. These Peerless mantles are the same size as the Coleman 21A mantles. Made in India.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
Coleman's Most Popular Sized Mantles. 4 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004344.
White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965 to 1971 200A, 220 & 228 F Lanterns. Also fits the 220G,
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
No Border Logo with "Reg." & "Lantern" for 1961 to 1964 200A, 220 & 228 E & F Lanterns
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
New Coleman made Spark Igniter. Comes in new packaging with instructions.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Coleman Lantern Logo for 1955 to 1961 220 & 228 E Lanterns
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.
Fits models Air O lantern, 327, 427, Slant 220 lanterns and CQ lamps
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
Used valve wheel screw. Will be in good condition.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.
Direction disk for the military lanterns. These came out of the old SMP factory.
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
Instruction Decal for 1945 to 1946 220C & 228C Lanterns. Also fits some 220D & 228D Lanterns
