- New!
Ventilator 339, Used - F150
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
Brass Vent Bolt for 243B, and all 241 Lanterns - this bolts down into the top of the frame to hold the vent.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
Used valve stem packing nut. Will also require a P01 graphite packing located HERE.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
This is special valve packing for the model 275 lantern. It is too big for other models. Has a 7/16 inch outside diameter, 1/4" inside diameter and is 3/8 inches long.
Others have said this also fits some older Coleman stoves like the 9D.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.
These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns.
Will all vary in wear and some may have rust .
Same as part number 288-1251
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.
These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295.
Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.
This product is not included in the OCP free shipping program.
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.
Need more information on the valve core? Click HERE.
Original one piece decals for the later SMP military lanterns. These are not reproductions. They came from the old stock of the factory when it closed.
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.
Rebuild kit for models 242, 242A, 242B, and the 242C lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
Rebuild kit for both the 275 and 275A lanterns. Cures most troubles.
Includes:
See Diagram in "Description" under photo at bottom left of this page
More parts for:
NOS Military Lantern globe channel. Crimps on burner frame to hold quadrant globe panes.
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
New reproduction pump cup assembly for 242 NL (No Letter), 242A , 242K, 243 , 246 and or any Coleman lantern or stove from the early 30's with a solid pump stem with no air hole in the middle. These are made for the USA manufactured Coleman pump shafts and will fit as they should. If yours is made in Canada, you will have to use a small file to widen the brass center to a cone shape to match your pump shaft - see the photos. Also known as part number 233-518
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.