Lanterns

Used burner frame for the 288 or CL2 lantern.

This one has paint chipping and top outside rim has a dent (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.

Fount dated 12-80. For models 220/228 H thru K.  Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).

Used generator nut for the 335 and 621 lanterns.

Used collar for a 275A. May show signs of wear.

Used valve stem nut for many Coleman lanterns.

NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.

Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.

This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)

Used collar for the 282 and 285 model lanterns

This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)

NOS burner frame for the model 222 Peak 1 Lantern

Unknown fuel tube. Measures 2 13/16 inches long.

Vent rod for the model 5114 propane lantern.

Collar assembly for the model 5107 and 5107A lantern. New old stock but has some scratches.

This is a used fount for the model 335 lantern. It is date stamped 1-77. It has surface scratches, but no dents. The inside looks excellent as it still has the reddish brown colored factory primer that is very visible.

Lamp valve for 130G, 130K 130P and 131P.  The bottom is threaded for a fuel and air tube to be attached.

Burner frame for the model 5152 lantern only. Will not fit the 5152A.

Spacer for lantern models 5154B, 5152D, 5153A, 5151C and 5150

Valve for the 5154B, 5152D, and 5153A propane lanterns with electronic ignition. Comes with ignitor cam and knob/screw.

Top cover for battery lantern, model 5355.

Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.

They will all show varying signs of wear/ wrench marks. 

Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.

New cotter pin for the 220B, 235 and other early style bails. This tiny cotter pin may be a little long and will have to be trimmed, but the width is correct to pass through the bail holes.

This is a used one piece filler cap off the Model 200A burgundy. 

Comes with a new gasket that you will have to install.

New nickel plated brass burner caps with round head. Fits most models of double mantle lantern and lamps.

Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.

This one is in very good condition.

NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

This is a used fount for the model 335 lantern. It is date stamped 1-75. It has surface rust, but no dents. Seems solid and the inside is not horrible.

This is a used steel collar for the model 242C lantern. Has a good amount of rust.

Used collar for the model 290A700T lantern. 

This is a used collar for the model 242B "Sport-Lite" lantern. It may have spots of rust or other discoloration/ stains.

Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel. 

We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

A graphite valve stem packing is included with each of these in case you end up needing to change them.

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 3/16"

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 5ft and diameter is 3/16"

N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

NOS Coleman shade holder for the old CQ style lamps.

May have a little rust from sitting around all these years.

This is a used collar for the 288 lanterns with the red arrow.

New valve assembly for the model 335 lantern.

Used Vent for Ash Flash lantern model 1010

Unknown fuel tube. Measures approx 2 3/8"

This used block if for the 275A lantern. Not sure of compatibility with the 275. 

Fits 275 or 275A lanterns. This is the flat one closest to the knob.

Used collar for the Canadian 331 Lantern.

Burner assembly for the model 5150 propane lantern.

Air intake tube for the model 5114 propane lantern.

Burner assembly for the model 5151 propane lantern.

Frame assembly for Leisure line lantern