Lanterns

This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)

Used collar for the 282 and 285 model lanterns

Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.

This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)

NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.

Used valve stem nut for many Coleman lanterns.

Used collar for a 275A. May show signs of wear.

Used generator nut for the 335 and 621 lanterns.

Fount dated 12-80. For models 220/228 H thru K.  Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).

This one has paint chipping and top outside rim has a dent (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.

Used burner frame for the 288 or CL2 lantern.

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 3/16"

Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. 

Has the single screw hole on the plunger cap.

This is a used valve assembly for a Canadian model 335 lantern.

Valve stem packing has not been changed but one will be included for you to change if needed.

Used collar for the model 290-700 lantern. Has red around the center circle rather than black.

Spacer Plate

Frame assembly for Leisure line lantern

Burner assembly for the model 5151 propane lantern.

Air intake tube for the model 5114 propane lantern.

Burner assembly for the model 5150 propane lantern.

Used collar for the Canadian 331 Lantern.

Fits 275 or 275A lanterns. This is the flat one closest to the knob.

This used block if for the 275A lantern. Not sure of compatibility with the 275. 

Unknown fuel tube. Measures approx 2 3/8"

Used Vent for Ash Flash lantern model 1010

New valve assembly for the model 335 lantern.

This is a used collar for the 288 lanterns with the red arrow.

NOS Coleman shade holder for the old CQ style lamps.

May have a little rust from sitting around all these years.

N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 5ft and diameter is 3/16"

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 3/16"

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"

This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"

Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel. 

We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

A graphite valve stem packing is included with each of these in case you end up needing to change them.

This is a used collar for the model 242B "Sport-Lite" lantern. It may have spots of rust or other discoloration/ stains.

Used collar for the model 290A700T lantern. 

This is a used steel collar for the model 242C lantern. Has a good amount of rust.

This is a used fount for the model 335 lantern. It is date stamped 1-75. It has surface rust, but no dents. Seems solid and the inside is not horrible.

NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.

This one is in very good condition.