Lanterns
P38 "John Wayne" Can Opener - R509
New old stock can openers. HERE is a link to a website with some good history on these. Good to have one of these handy for emergencies or camping.
200A Valve Stem with Nut, Reproduction - R576
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Mixing Chamber New Style Plated - E1140
This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar.
- New!
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Valve Stem 200A, Used - E1004
Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.
Lamp Handle Fiber Spacer Used - E1098
This is the Bakelite top finish spacer on a CQ lamp handle. It is in used condition.
Pump Assembly, 220C Thick Steel Cap, Used - E1296
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
200A Used Fuel Tube Spring - E1023
Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.
Mixing Chamber Used New Style - E1414
This is a used mixing chamber. May or may not have a vent rod and air tube screw.
- 3% less
- New!
228 Vent, Old Style Used - U865
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
Valve Assembly Old B Style Used - E1285
This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.
Gas Bottle, 8 oz. - R321
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
- New!
Mixing Chamber, Old Style, Used - E1185
This is a used older style brass mixing chamber for the 220-228 series lanterns.
Burner Tube Brass 2 3/4 - E1129
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
242C Steel Collar, Used - E1299
This is a used steel collar for the model 242C lantern. Will vary in amount of rust and wear.
Vent 220, Old Style, Used - U860
This is a used vent. It will fit models 220B through 220E.
Has paint chippings and a small bulge towards by the ball nut opening (see photos)
Reproduction Canadian Ball Nut 242 - R575
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.
Small valve stem packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - P02
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Valve Stem Used - E1596
Valve stem for Quick-Lite lanterns.
These have not been serviced or cleaned and may need a new P02 packing which is HERE.
Alcohol Bottle 8 oz. - R323
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Eccentric Block B - S146
Reproduction eccentric block for the very early 220B lantern that took the longer eccentric. Will not work in the later 220B or other 220 series lantern.
Burner Tube Steel - E1357
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
252 Collar - X1
Used collar for the milspec lantern. They have a few small spots of missing paint here and there.
- New!
Quick-Lite Air Stem, Reproduction - S130
Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.
Burner Tube Steel Old Style - E1101
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
- New!
Air Intake Tube Steel, NOS - E1555
Steel air intake tube for the old Quicklite lanterns and CQ lamps.
- New!
- New!
Filler Cap Nickel, Used - E1395
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.