Lanterns
Bail Handle, Used - E1687
Used bail for the models 321, 325, 331, 335, 339 and other similar Canadian models.
Bail Reproduction Bent - B100
Reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Looks identical to the original.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.
Vent Bracket, Used - E1021
Used Vent bracket.
Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern.
288 Knob, Used - E1399
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
- New!
Lamp Valve - E1111
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
- New!
Rebuild Kit - 220 & 228 Lanterns - K16
Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.
Includes:
- 4 Peerless mantles for your lantern
- 1 Reproduction generator
- 1 Leather replacement pump cup for the bottom of the thumb operated air pump
- 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
- 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed
See Diagram in "Description" under photo at bottom left of this page
Pump Assembly Neoprene Used - E1561
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Direction Disk 220J Used - E1200
Used direction disk for the later double mantle lanterns such as 220/228, J-K. Will show signs of wear but still be in good condition.
Quick-Lite Filler Plug - R354
Amish style filler plug for the early Quick-Lite lanterns and lamps. Does not use an air stem and requires a hand pump.
- New!
Ball Nut 275 Checkered, Used - E1075
Used ball nut for the model 275 lantern. This is the checkered variety.
Valve Assembly Quicklite NOS - E1651
New old stock valve assembly for the QuickLite model 327 lantern.
- Free Shipping
O-Ring Single #9 Viton - S89
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #9.
Jamb Nut, NOS - E1627
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
242 Bail Used - E1531
This is a used bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Will show wear and rust and such, but be solid.
Valve Stem - E1228
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
- Free Shipping
O-Ring Single #6 - S84
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #6
- New!
242 Filler Cap Wrench Marks - E1050
This is a used filler cap for the 242 lanterns. These have wrench marks on them. They will work just fine if you need a cheap filler cap. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove. Comes with a new gasket that you will have to install.
Pump Assembly Plastic Cap, Used - E1426
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
- New!
- Free Shipping
O-Ring Single #7 - S90
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7
It has been reported that the 285 valve stem uses 2 of these.
Bail Handle Reproduction Bent - B200
Reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.
Fuel and Air Tube Needle Used - E1077
Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.
Burner Assembly Steel Used - E1660
Burner Assembly for the model 288 lanterns. The burner tubes are steel. Will vary in wear.
- New!
Filler Cap Brass Used - E1307
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Burner Tube - R319
Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Burner Tube with Nut - Steel - E1127
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
- New!
- New!
Burner Frame, Used - U930
This is a used old style burner frame originally used on the black band 200A Lantern. Looks like someone may have replaced the tabs - they are supposed to be short.
- New!
228 Vent, Small Frame, Used - U887
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
242B Nickel Collar, Used - E1672
This is a used collar for the model 242B lantern. It may have spots of rust or other discoloration/ stains.
- Free Shipping
O-Ring Single #8 Viton - S88
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.
- New!
Filler Cap Dark Green Used - E1431
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.