Lanterns
200 Vent Short, Used - U856
Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).
- Free Shipping
O-Ring Single #7 Viton - S87
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.
It has been reported that the 285 valve stem uses 2 of these.
Valve Wheel Black, Old Style, NOS - E1679
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
Valve Stem N.O.S - E1595
N.O.S Valve stem for the model 335 and 339 lanterns.
Has a small chip on the valve wheel.
242 Burner Frame, Used - BF503
This is a used Burner frame for the 242A through C lantern. Will also work on the 247.
Is stamped with 3000.
Air Intake Tube Steel - E1397
Air intake tube for model 117A, 118A, 119A, 132A 133, 134, 134A, 134P, 134G, 143, 150B, 150G, 150R, and 150I lamps. Also early model 220 and 228B lanterns that use the two piece air tube.
Coleman Unknown Valve Stem #1 - E1652
Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.
Quick-Lite Collar, Used - E1565
This is a used collar for the model 327, 427, and similar lanterns. Some will have some surface rust - all will vary with wear.
Generator Nut, Reproduction - S168
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Mixing Chamber Wide, Used - E1635
Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.
Fount 220/228, Old Style, 12-62 - U891
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62.
Has paint chipping and some rust (see photos)
220F Vent, Small Frame - U882
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Direction Disk #9 - E1068
Unknown Coleman direction disk. I do not know what it goes to. It is a small disk with only an 11/16 inch diameter.
- New!
200 Fount, Used - U901
This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)
- New!
Mixing Chamber Used, with Vent Rod - E1367
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
Filler Cap 242 Nickle Plated, Used - E1630
This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Comes with a new gasket for you to installed if needed.
Sears Valve Wheel Screw, Used - E1577
These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.
Mixing Chamber Aluminum - E1568
Aluminum mixing chamber for most double mantle lanterns and lamps. Coleman experimented with aluminum for a few parts back in the old days. I believe it was discovered that aluminum could not hold up to the heat. Probably more of a display piece than for using.
200A Vent Short, Used - U857
Used short style vent for the 200/200A lanterns made in 1963 and after.
This vent has some scratches/scuffs and paint chippings (shown in photos)
- 67% less
Filler Cap Brass Outer Cap Used - E1179
This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
242C Collar Used - E1673
This is a used collar for the model 242C lantern. All will vary with wear and discoloration.
Fount 220/228, New Style, Used - U894
Fount dated 5-77 for the model 220/228 Lanterns, models H thru K. This fount has some scratches, paint chipping, and rust - see photos.
Air Intake Tube Old Steel - E1138
This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.
Burner Assembly 286, Brass - E1270
New burner assembly for the model 286 lantern. The burner tube is brass.
Valve Assembly, Used - E1356
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
- New!
Ventilator 339, Used - F150
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.