Lanterns

Used bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.

Original Coleman Lantern Reflector, will only fit on 200's.

Handle is in really good shape, only has a couple small chippings.

Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.

This one is in very good condition.

Original Coleman Lantern Reflector, will only fit on 200's. Lantern is for illustration purposes only.

The handle has some chippings and some small cracks in the wood but is still solid.

This is a used vent for the model 5114 propane lantern.

New old stock filler cap and chain for the military lantern. Will also fit any Coleman lantern or stove that used the standard size filler cap. I am 99% sure these filler caps came from the old SMP factory.

Used Generator seat for the military lantern.

Used generator body only. This is only the brass tube of the generator and the gas tip. May or may not have the internal spring and packing tube. No needle is with this.

NOS valve assembly for the Milspec lanterns. 

This is an original 220 Coleman vent. The black porcelain finish was custom done by Independence Porcelain Enamel (IPE). This is for the late 220F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.

This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a used black steel collar for the 200A lantern. Steel black collars were used in 1952 - early 1953. Condition of each collar varies. A lot of the black is worn off and has rust.

New old stock lamp finial.

New old stock finial for lamp.

Used top half of the burner assembly for a slant lantern or lamp.

Nickel Tip Cleaner Assembly with air piece. Does not have the eccentric block.

Fuel and air tube for lantern models 220/228B, 220BX, and 220/228C. Earliest style of fuel and air tube. 

Used Bail Handle

Used burner frame for the 327 and 427 lanterns. This frame is missing the bail handle.

Used flat baffle plate used on the very early 327 Quicklite lanterns.

Black Vent & Bail for Northstar Lantern.

Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.

This is a used lamp handle for the early lamps like the Model M and other Pre CQ Lamps. Some might show signs of wear. It is 4 3/4 inches long.

This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.

These are early style shade holders for the Air-o-Lite Lamps

Used 242 Valve stem.

Packings have not been changed, if you need one they are HERE

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

This is a used ventilator for the model 220B through 220E lantern. 

This vent has a few paint chippings. (see photos)

This is a used ventilator for the model 220B through 220E lantern. This vent has paint chips (see photos)

This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.

It will work for any 220/228H through 220K type models.

This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)

This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62. 

Has paint chipping and some rust (see photos)

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns. 

Is stamped with 3000.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247. 

Is stamped with 3000.

Used fount for the model 327 Quick-lite lantern. Dated 9-29.

This one has some dents and scratches but otherwise in nice condition (see photos, the dents are hard to see)

This is a used fount for the model 242 Lantern. It is date stamped 4-47. Has some paint chipping and a couple very small dents. The sunshine logo looks faded but is there.

It will work for models 242, 242A, 242B, 242C, 243, 243A, 247, and 242K.

This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)

Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.

They will all show varying signs of wear/ wrench marks. 

Spring for the inside of the 236 generator.

Used vent for the model 275 and 275A. Has two chips - shown in photos.

This is a used fount for the model 335 lantern. It is date stamped 1-77. It has surface scratches, but no dents. The inside looks excellent as it still has the reddish brown colored factory primer that is very visible.

Used Unleaded Fount for the model 295 lantern. Has some scratches. It is dated 1-95.

Used Vent for Ash Flash lantern model 1010

Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.

This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.