Lanterns

This is a used ventilator for the model 220B through 220E lantern. 

This vent has a few paint chippings. (see photos)

This is a used ventilator for the model 220B through 220E lantern. This vent has paint chips (see photos)

This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.

It will work for any 220/228H through 220K type models.

This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)

This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62. 

Has paint chipping and some rust (see photos)

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns. 

Is stamped with 3000.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.

This one will need a new burner cap or screen.

Is marked with 3000.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247. 

Is stamped with 3000.

Used fount for the model 327 Quick-lite lantern. Dated 9-29.

This one has some dents and scratches but otherwise in nice condition (see photos, the dents are hard to see)

This is a used fount for the model 242 Lantern. It is date stamped 4-47. Has some paint chipping and a couple very small dents. The sunshine logo looks faded but is there.

It will work for models 242, 242A, 242B, 242C, 243, 243A, 247, and 242K.

This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)

Spring for the inside of the 236 generator.

Used vent for the model 275 and 275A. Has two chips - shown in photos.

This is a used fount for the model 335 lantern. It is date stamped 1-77. It has surface scratches, but no dents. The inside looks excellent as it still has the reddish brown colored factory primer that is very visible.

Used fount for the model 288 lantern. Dated 5/88. Slight rust and chipping. No dents.

Used Unleaded Fount for the model 295 lantern. Has some scratches. It is dated 1-95.

Used Vent for Ash Flash lantern model 1010

Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.

This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.

Steel air intake tube for the old Quicklite lanterns and CQ lamps.

NOS fuel tube for the slant 220 and 228 lanterns.

Used burner assembly for the old model 327,427, also for CQ and Air O Lite lanterns. Will also work on other lamps that would have originally taken the Q99 generator.

Used direction disk for the 220/228H lantern. Will show signs of wear but still be in good condition.

Reproduction generator nut for the 252 military lantern. Made of brass.

Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.

Will come with a new gasket for you to install if needed.

This is a used filler cap for the 242 lanterns. These have wrench marks on them. They will work just fine if you need a cheap filler cap. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove. Comes with a new gasket that you will have to install.

Used valve body for the slant lanterns and lamps.

This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.

This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.

This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.  

Comes with a new gasket for you to installed if needed.

Used burner frame for the models 228H and 228J lanterns.

Used burner frame for the models 228H and 228J lanterns.

Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.

Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)

Reproduction vent rod for the model 236 and 237 lantern. Made of solid brass.

Reproduction nickel plated vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.

Used ball nut for the model 275 lantern. This is the checkered variety.

Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.

These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.

Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).

Used tall style vent for 200/200A lanterns made in 1962 and before. This vent is the slightly darker cherry red and is in great shape. This vent has paint chipping and has very tiny white dots all over it - color looks slightly faded (see photos)

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.

Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.

They will all show varying signs of wear.

This is a used older style brass mixing chamber for the 220-228 series lanterns.

Used Lantern Base Dark Green.