Lanterns

These came out of the old SMP factory. This is the washer that goes behind the pump nut on an SMP military lantern.

Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.

Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.

This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

This is a used collar for the 220F lantern.

This is a used collar for the 228F lantern.

Condition will vary.

Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear. 

This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.

Stainless Steel hook for hanging lanterns and other items.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

Used valve wheel screw.  Will be in good condition.

These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.

Generator Nut

Generator Sleeve

Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Frame bolt. Fits the 5107C, 5114C, 5151, 5152. May fit others.

This is the small part that attaches to the filler cap screw so you can hook the chain to it.

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.

Fuel tip used on the end of the fuel tubes of early 220/228B lanterns, 236 and some lamps.

O ring.

New rubber pip for the re-buildable NRV type check valve used on the 242, 242A, and the M1950 stove.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. 

Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.

Filler plug gasket for the model CQ lamps,327 Quicklite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket. Also fits the 523 military stove.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Fits the fuel tube on all appliances that have a plastic fuel and air tube.  

Models: 214, 282, 285, 288, 290, and 295.

Also fits: 

• The fuel tube on the 550B stove
• On the propane regulator of a model 2000004489 Perfect Flow Skillet (reported by a fellow Coleman user). Propane regulator #9933-5251

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.

It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole. 

Old part number 115-1361. 

This will not seal they typical Coleman lantern cap.

Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.

Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.

Cam Follower

This is a used pump square nut.

Comes with one square nut ONLY.

New burner screen for the models 236, 237 and 249.

Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

Used Vent bracket. 

Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern. 

Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns. 

Will all vary in wear and some may have rust .

Same as part number 288-1251

New gasket for the military lantern parts well cap.

Used Base bracket for the Military lanterns.

Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

Unknown used ball nut. Kind of like half a ball nut.

Used figure 8 piece as used on the old Q style burner.

Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.

This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.