Lanterns
1/4" Valve Stem Bushing - S137
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
130 & 131 Lamp Valve, NOS - E1176
Lamp valve for 130G, 130K 130P and 131P. The bottom is threaded for a fuel and air tube to be attached.
200 Burner Frame Washer Kit - K14
These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.
New 200 burner frame Pal Nut is HERE.
New 200 burner frame Nut is HERE.
- New!
200 Fount, 1/63, Used - U900
This is a used fount for the model 200A lantern. Has some paint chipping, scratches/scuffs and two very small dents you can only see in certain lights (see photos). Otherwise in nice shape - inside of tank looks good too.
200 Fount, Used - U901
This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)
200 Fount, Used - U902
This is a used fount for the 200A lantern dated 9-60. Has some scratches/paint chipping and a dent by the pump assembly (see photos)
- New!
200 Vent Short, Used - U854
Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)
200 Vent Short, Used - U855
Used short style vent for the 200/200A lanterns.
This vent has some scuffs/scratches and a little paint chipping (see photos).
- New!
200 Vent Short, Used - U856
Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).
200 Vent Tall Used - U852
Used tall style vent for the 200/200A lanterns.
This one has some scratches and paint chipping (see photos)
- New!
200 Vent Tall, Used - U850
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent is the slightly darker cherry red and is in great shape. This vent has paint chipping and has very tiny white dots all over it - color looks slightly faded (see photos)
200 Vent Tall, Used - U850
This is a used tall style vent for the 200 and 200A Lantern.
Has some paint chips (see photos)
200 Vent Tall, Used - U853
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent has some rust and chippings (see photos).Â
200A Collar, Used - U840
This is a used collar for the model 200A lantern.
It may show signs of wear/scratches. Each collar may slightly vary in wear.
200A Fuel Tube Reproduction - R304
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
200A Reproduction Burner Frame - R353
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
200A Used Fuel Tube Spring - E1023
Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.
200A Valve Stem with Nut, Reproduction - R576
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
200A Valve Stem, Reproduction - S05
Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
200A Vent Bracket Short Reproduction - R307
Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.
200A Vent Bracket Tall Reproduction - R314
New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.
200A Vent Short, Used - U857
Used short style vent for the 200/200A lanterns made in 1963 and after.
This vent has some scratches/scuffs and paint chippings (shown in photos)Â
201 Burner Tube - S161
Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.
220 Burner Frame, Used - U920
Used burner frame that will fit models 220B through early 220F through approximately 1971.
- Free Shipping
220 Burner Screen - S30
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
220 Filler Cap Insert, Used - E1222
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
220 Lantern Reflector - LR3
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)
220 Lantern Reflector - LR4
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one is in very good condition.
- New!
220 Old Style Vent, Used - U862
This is a used ventilator for the model 220B through 220E lantern.
This vent has a few paint chippings. (see photos)
220 Old Style Vent, Used - U863
This is a used ventilator for the model 220B through 220E lantern.
Has some paint chips and scratches (see photos)
220/228 Air Tube Screw Phillips - S74
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
220/228 Eccentric Block, Used - S119
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
- New!
220/228 Fount, New Style, 5-73 - U893
This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.
It will work for any 220/228H through 220K type models.
220/228 Valve Bushing Set - S134
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
220F Vent, Small Frame - U880
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
220F Vent, Small Frame - U882
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
222 Fuel Cap and Lanyard - E1158
Used filler cap with lanyard for the small backpacking lanterns - in very nice shape. Will also fit most other lantern and stoves that use the standard size filler cap. Comes with a new gasket that you will have to install.
- New!
- New!
228 Burner Frame, Old Style, Used - U923
Only 1 left in stockThis is a used burner frame that will fit models 228B through 228F.
Has a bit of rust
- New!
228 Vent, Old Style Used - U865
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
228 Vent, Old Style Used - U866
This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).
- New!
228 Vent, Old Style Used - U867
This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)
- New!
228 Vent, Small Frame, Used - U887
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.