Other Brands

Generator nut for Thermos lanterns.

Thermos generator for stove models 8420, 8421, 8430, and 8431. New generator includes new gas tip, spring, and tip cleaning wire.

Thermos generator for models 8315 and 8316. May show signs of tarnish but is new old stock. New generator includes new gas tip, spring, and tip cleaning wire.

Eccentric lever assembly for the inverted lantern.

Used valve for the model 8326 Thermos lantern.

Used generator for the model 8326 Thermos lantern. These fit also the Wards/Western Field Model 60-9523 and some AGM lanterns that use part number S7706.

These generators come in different conditions - all show wear and signs of use. The pricker rods are good in each and move freely.

Thermos stove generator for models 8422, 8425, 8426, 8427, 8428, 8429, and 8432. New generator includes new gas tip, spring, and tip cleaning wire.

Thermos generator for models 8311 and 8312. May show signs of tarnish but is new old stock. New generator includes new gas tip, spring, and tip cleaning wire.

Globe nuts for the Thermos and Kamplite inverted lanterns.

Generator for AGM lanterns. Measures 3 1/8 inches long. Fits the AGM model 3025 lantern. Thanks to Joe P. for this information.

Generator for an AGM lantern. Measures 3 9/16 inches long.

Used burner assembly for the Thermos 2 mantle lantern. In good shape.

Burner cap with 3 holes for Thermos lanterns.

Burner cap with 5 holes for thermos lanterns.

This is a used vent.  Has chipping and a little rust as shown in photos.

Used Vent for Ash Flash lantern model 1010

The Canadian 990 globe was made to fit the model 331 lantern. Does not fit any other gas lantern model. Very rare globe to find these days. Will also fit the Thermos lantern models 8311 and 8312.

This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.

Short pump assembly for Thermos lanterns. Pump barrel measures 3 inches. Will most likely need a new O-ring kit which are HERE.

Generator for some model of AGM lantern. Measures only 1 9/16 inches long.

Decal for the Preway Model P4521 stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Generator for some model of AGM lantern. Measures only 1 9/16 inches long. Missing the tip cleaning needle.

Used collar for the Thermos model 8326 lantern.

Used collar for the Wards/Western Field Lanterns. These are used and in decent shape.

This is a used Thermos lantern style vent. Excellent condition - no dents, scratches or chips.

Used bail for the Thermos model 8326 lantern. These also fit the Wards / Western Field Model 60-9523 lantern.

This is a used Western Field Thermos vent. Small imperfections and one chip, but in excellent shape.

Filler cap. Appears to be made of aluminum. Roughly the same size as the common Coleman filler cap. 

Thermos Lantern Pump. Measures 4 7/8 inches long from end to end.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

Thermos generator for inverted lantern models 8319 and 8321. Also fits Kamplite and JC Higgins inverted lanterns. May show signs of tarnish but is new old stock. New generator includes new gas tip, spring, and tip cleaning wire.

This is a used bail handle for a non Coleman made lantern. It is approximately 5-3/4" inches wide is approximately  5-3/4" inches high.

Decal for the Punker Alcohol Stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Decal for the Thermos lantern. It is approximately 2 1/2 inches long and is 1 1/4 inches high at the widest point. The background silver is too sparkly on these. Reduced price to sell.

New old stock generator for the Aladdin PL1 lantern.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is a used collar for a model 476.74060 Sears lantern. Wear will vary.

This is a used collar for a model 476.74070 Sears lantern. Wear will vary.

These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.