Stoves
M1950 Military Wrench Reproduction - R554
Original reproduction wrench for the model 536 or M1950 stove.
Permatex Indian Head Shellac - R507
This is a gasket sealer that many use for sealing valves to tanks. Is flexible when dry and offers good fuel resistance.
Steel Vaporizer Screen - E1218
Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
P38 "John Wayne" Can Opener - R509
New old stock can openers. HERE is a link to a website with some good history on these. Good to have one of these handy for emergencies or camping.
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Check Valve, Large - E1626
NOS check valve for the 345 Kerosene stove, 348 Alcohol stove, the 5B radiant heater and some large kitchen range type appliances. This is larger than all the other Coleman check valves that are commonly used in lanterns and military applications. Width from side to side on top of the threads is 5/8".
4-36 x 5/16 Brass Screw - S61
This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..
- 3% less
Block and Needle Assembly - E1109
Block and Needle Assembly. Measures approximately 4 1/4 inches long.
Screw Burner Support, Used - E1576
Burner support screw for a 502 stove. Each stove requires 3 total.
502 Grate Used - E1451
This is a used stove grate for the 502 Coleman stove. It will show signs of being used.
Small valve stem packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - P02
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Air Stem Reproduction - R416
This is a reproduction air stem for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.
4-36 x 5/16 Screw Steel - S62
This is a screw for 242 pumps where the top of the pump fits inside the fount and for other applications with this thread.
Air Stem Long New Style - E1048
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
- 73% less
Parts Tube - E1418
Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.
Valve Assembly 502, Used - E1463
Used valve assembly for the model 502 stove. Valve stem packing has not been changed but one will be included for you to change if needed.
Generator Coil - E1018
NOS Generator Coil for models 425s, 415C, 415D, 416 B. 416C, 2G, 9G, 2H, 9H, 2B, 9A, 9B, 417B, 4F, 6F. 6B, 412B, 421, 421D, 391 and 391A.
Fuel Tube HGP - R409
Reproduction fuel tube for the Model 457, 460 and 575 Handy Gas Plant. Also fits stove models 375, 375A, and 376.
Pump Assembly Neoprene Used - E1561
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
HGP Fuel Cap, NOS - E1655
NOS, HGP cap. Fits models 457, 457G, 575, 460, 470G Handy Gas Plants. Also fits the 465 Tank.
Direction Disk, Small - E1629
NOS Direction disk. Small disk with little less than a 3/4 inch diameter. Mostly used on propane stoves - will be way too small for a GPA lantern or stove.
- Free Shipping
O-Ring Single #9 Viton - S89
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #9.
- Free Shipping
O-Ring Single #6 - S84
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #6
Pump Assembly Plastic Cap, Used - E1426
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Cap Insert Reproduction - R424
This is a reproduction filler cap insert for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.
- New!
530 Valve Wheel, Used - E1392
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
- Free Shipping
O-Ring Single #8 Viton - S88
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.
Burner Bowl, Used - E1527
Used burner bowl for the 502 stove. These are in good shape and may have some rust. The photo is an example, not the actual.
220 Filler Cap Insert, Used - E1222
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
Valve Stem, NOS - E1252
Valve stem only. Fits the 413E, 413F, 413G, 413H, 425F, 426E, 442, 442A, Sears Models 476.72303, 476.74980, 476.72302, and 476.74970. Comes with a new packing installed. Also known as part number 413A2521.