Stoves

Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.

Unknown ceramic material type of burner button used on some heaters and stoves. This has a diameter of 3/4 and is 3/4 tall.

NOS black knob. Same knob as part number 5445-1491 only a different color.

Valve and generator for stoves 393, 396, 396LC, 396A, 396A-LC, and 397.

Gas tip.

Used top half of a 530 stove. Missing all of burner supports.

Generator Coil For generator 940-262. Measures 9 1/8 inches long and has a diameter of about 1/4 inch.

Gas tip

Knob

This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

This is a used stove handle for the model 413H stove and many others. It measures 5 3/4 inches across. Will show signs of rust and wear.

These are new old stock and have a bit of rust on them from sitting on a shelf for decades. Comes with a packing from the factory. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle.  If your stove has been updated to a later valve style then this would not fit.

The needle and holder for this is part number 471-2381 HERE.

A whole new valve and gen would be part number 413B6601.  That is the valve that fits the 413E and 413G stoves.

Cleaning needle for the Canadian model 414 stove. May have some rust.

For Canadian 432 and 433 Easi-Lite stoves.

Used collar for the model 500A stove.

Manifold pipe. It is 10 inches long.

Burner for the model 522 military stove.

Used top half of a 530 stove - Comes with burner supports.

NOS valve stem for many of the older Coleman stoves. Compare your diagram with the part number 412-253 to verify it will fit. Will not fit into the 414, 424, 425, 426 series stoves.

Manifold pipe. It is 8 inches long.

Auxiliary valve. Fits 417B, 4F, 6F, 6B, and 412B Stoves.

Unknown Coleman long valve stem as used on early Coleman stoves that took a short screw in needle on the end. The entire part is 12 1/4 inches long. Has some surface rust  from sitting on the shelf for decades. 

Used legs for the 520 military stove.

Burner fillers for the model 3F stove.

This is a used latch that was used on many stoves. Known to fit 413G. It may fit others.

Used combo pre-heater cup and gen nut for the M1950 stove.

Bracket screw for the model 500 and 500A stove - Screw ONLY.

If you need just the bracket it is HERE.

Master Inlet Control Valve

Valve stem for 890 series kitchen range type stoves.

NOS Valve for tanks 457, 465, and 653D.

Gas tip

Maintenance kit for the Peak One model 3004 and 3008 stoves.

Gas tip for the model 435 stove.

Valve and hose for the 9720 stove.

Gas tip.

Used on Coleman Air-O-Gas Range No. 322 and Coleman Air-O-Gas Stoves Nos. 329, 600, 601, 602, 620, 621, 622, 623, 624, 625, Coleman Cooker Range Nos. 17, 17-0, 17-10, 18, 18-0, 18-10, 364, 364A, 366 and Coleman Cooker Stove Nos. 12, 12-3, 86, 86-4, 360, 361, 363, 365.

Pre-heater valve for the 463-398 burner. Used on 501 and 751 burner

Don't know the part number for this valve and generator. It measures 10 1/4 inches long from tip to end of nut. 

Used carry case for the M1950 stove. Can also be used for other military stoves such as the 520. Will not fit the 530. Has a couple dents and scratches (see photos)

Used corrosion resistant aluminum cooking kit.
Lid is 6" frying pan, and bottom is a 2 qt. sauce pan - does not come with handle.

Has some dents on the lid, bottom, and around the edge where the lid goes on (see photos)

Used case for a 530 stove. Has wear from age and use but still in good condition.
The 530's were made from 1946-1950 for both the U.S. and the Canadian market.
Originally these were called the "G.I. Pocket Stove" because the G.I.'s returning home enjoyed using the 520 stove made for the military. 

Bracket for the model 500 and 500A stove - Bracket ONLY

If you need just the screw it is HERE.

This is a used pip holder cup for the M1950 stove pump. Comes with a new rubber pip.

Pre Heater Stem Assembly for the Marine Stove

Gas tip

Valve assembly

Unknown Coleman valve and generator. I can't figure out what this fits or a part number for it. Measures 11 1/2 inches long.

Generator tube only for the model 950 generator.

Valve stem