Stoves
- New!
- New!
- New!
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- New!
- New!
- New!
Valve Wheel Maroon, Used - E1178
Used maroon valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.
GPA Starter Toolbox Kit - K22
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
- 4 new Coleman check valves
- 10 Leather pump cups - pre-oiled
- 5 Neoprene rubber pump cups
- 10 Large valve stem packings for 1/4"
- 5 Small valve stem packings for 3/16"
- 10 Generator tube packings
- 10 One-piece fuel cap gaskets
- 10 Three-piece fuel cap gaskets
- 10 Cap gaskets sized for the 242 or 500 stoves
- 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns
530 Valve Wheel, Used - E1392
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Valve Wheel Red Old Style, Used - S111
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
M1942 Wood Knob - S58
Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.
- Free Shipping
Stencil for Model 2 Stove - E1180
Vinyl adhesive-backed stencil for Model 2 stove. Stick it on your tank, paint, then remove.
- Free Shipping
Stencil for Model 9C Stove - D154
Vinyl adhesive-backed stencil for Model 9C stove. Stick it on your tank, paint, then remove.
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
M1950 Pump Pip Cap, Used - E1616
This is a cap for the end of the M1950 pump. This screws into the bottom of the pump.
M1950 Pip Cup, Used - E1143
This is a used pip holder cup for the M1950 stove pump. Comes with a new rubber pip.
Pump Assembly Leather Used Square Nut - U810
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Valve Minus the Generator, NOS - E1248
NOS valve minus the generator and valve wheel, for the model 425 series stoves.
Stove Bracket, Reproduction - E1305
Bracket for the model 500 and 500A stove - Bracket ONLY
If you need just the screw it is HERE.
10-24 x 1/4 Stove Bracket Screw, Reproduction - S63
Bracket screw for the model 500 and 500A stove - Screw ONLY.
If you need just the bracket it is HERE.
- Free Shipping
500 Generator Needle, Reproduction - R217
Reproduction generator needle for the model 500 and for the 345 kerosene marine stove.
Leather Pump Cup Kit - C005
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
Generator Coil, NOS - E1124
NOS Generator Coil.
Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.
Filler Cap Brass New - R315
This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
Valve Wheel Red New Style, Used - S114
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
502 Grate Used - E1451
This is a used stove grate for the 502 Coleman stove. It will show signs of being used.
HGP Fuel Cap, NOS - E1655
NOS, HGP cap. Fits models 457, 457G, 575, 460, 470G Handy Gas Plants. Also fits the 465 Tank.
Generator Coil - E1018
NOS Generator Coil for models 425s, 415C, 415D, 416 B. 416C, 2G, 9G, 2H, 9H, 2B, 9A, 9B, 417B, 4F, 6F. 6B, 412B, 421, 421D, 391 and 391A.
Unknown Generator Coil #7 - E1647
Generator coil. Measures 7 1/4 inches long and the width is 7/32". Made of steel.
Stem Assembly (Lighter) - E1072
Stem (lighter) assembly. This was the last style used on the 500B Canadian Stove, will also work on the 500 and 500A. This is a rare part.
Generator Coil - E1345
Generator Coil. Rusty.
Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.
- Free Shipping
Burner Cap & Rings - C054
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
Valve Wheel Red, Used - E1151
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.