Stoves
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- Free Shipping
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
- Free Shipping
5114 Propane Gasket - S53
This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.
This fits many applications for propane appliances.
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
M1950 Burner Bowl - E1271
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These will not fit the 530 stove without using a 1950 generator and a 530 needle.
Permatex Indian Head Shellac - R507
This is a gasket sealer that many use for sealing valves to tanks. Is flexible when dry and offers good fuel resistance.
Short Pump Plunger, Plastic Cap - C037
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
Stove Bracket, Reproduction - E1305
Bracket for the model 500 and 500A stove - Bracket ONLY
If you need just the screw it is HERE.
- Free Shipping
O Ring - S23
O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400A.
Two required for the model 550 stove.
Generator Coil - E1224
Generator Coil For generator 940-262. Measures 9 1/8 inches long and has a diameter of about 1/4 inch.
Burner Fillers and Cap Used - E1291
Used burner fillers and cap for the model 502 stove. Has some rust but seems to be in good shape.
220 Filler Cap Insert, Used - E1222
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
Red Knob - S172
This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.Direction Disk 5418 Used - E1194
Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.
NOS Metal Pump Cap - E1405
NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.
M2 Valve No Stem/Knob - E1003
This is a new old stock pre-heater valve for the M2 military stove. Does not have the valve stem or wheel (knob).
Military Funnel Chain - E1643
Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.
NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit. No other sizes of chain are currently available that are an exact match to what was used.
- Free Shipping
Cap Gasket HGP - S50
This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
- Free Shipping
Unknown Fuel Tube - E1592
Only 1 left in stockUnknown fuel tube possibly for a stove. Measures 5 3/4" long.
Don't know if it is used or NOS.
Valve and Generator - C029
New Coleman made valve and generator. This part will fit: 2G, 2H, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 421, 421C, 421D, 421E, 425, 425B, 425C, 425D, 425E, 425F and Sears 476.72301, 476.74960, and 476.72244.
- New!
M1950 Pip Cup, Used - E1143
This is a used pip holder cup for the M1950 stove pump. Comes with a new rubber pip.
NOS Unknown Valve Stem Long #2 New - E1519
Unknown Coleman long valve stem as used on early Coleman stoves that took a short screw in needle on the end. The entire part is 12 1/4 inches long. Has some surface rust from sitting on the shelf for decades.
Valve Assembly - E1354
Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.
P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).
- 67% less
Filler Cap Brass Outer Cap Used - E1179
This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
- Free Shipping
Filler Cap Gasket for 1 Piece Cap - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - S42
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
- Free Shipping
- New!
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
- Free Shipping
O-Ring Single #7 Viton - S87
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.
It has been reported that the 285 valve stem uses 2 of these.