Stoves

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Fuel Air Tube for the 413 series and 442 series 2 burner stoves. NOS.

This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.

This fits many applications for propane appliances.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.

Also known as part number 3000005094.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.

This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.

Fuel and Air Tube

Needle And Rod for the 396, 396A, 396B and 397 cabin stoves.

Valve stem complete for stove 393 396, 396LC, 396A, 396A-LC, and 397

Lighting lever for stove

Valve and generator for stoves 393, 396, 396LC, 396A, 396A-LC, and 397.

Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves

Valve assembly for the 400B, 3024, 442  and 440 single burner stoves.

This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203

Valve stem for the 425, 425B,C and E stoves

Lighting stem.

Fuel and Air Tube for many stoves. Same as part number 425-6461.
Fits 2G, 2H, 4F, 6B, 6F, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 417B, 425 models, 500, &500A.

Valve minus the generator for the model 425 series stoves.

New Coleman made valve and generator. This part will fit: 2G, 2H, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 421, 421C, 421D, 421E, 425, 425B, 425C, 425D, 425E, 425F and Sears 476.72301, 476.74960, and 476.72244.

Used valve Stem for the 425 F and G  stove only, will not fit earlier models. Measurements:  just over 1-3/4" long and 1/4" diameter. You will also need a P01 graphite packing for this HERE.

This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem is 1/4".

Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443  Instant Light, 2 & 3 Burner Stoves

Control Valve & Generator Assembly Complete 414/428

Fuel Tube

Parts Kit

Regulator Assembly Fits the 445A, 450A and 3021 Stoves

Large leather pump cup for the T-Handle pumps, kitchen ranges, and other larger appliances. The flat portion of the cup measures 1" wide. For pump barrels with a 1 1/4 inch diameter.

This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.

Needle & Holder

Gas tip

Gas tip.

Gas tip.

Reproduction generator needle for the model 500 and for the 345 kerosene marine stove.

Used Fuel Valve Assembly

Reproduction generator nut for the 500 and 500A stove.

This is a used stove grate for the 502 Coleman stove. It will show signs of being used.

This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.

Used Valve Regulator Assembly.

Valve assembly Fits 508A, 508B, 533 and the 533A

Eccentric block for the model 530 stove.

Air stem for the 530 stove.

Pump Clip

Cap Gasket for M1942 & M1950 stoves.

Grate for 5404 and 5409 stoves. Good shape.

O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400A.

Two required for the model 550 stove.

Made by Coleman - this is the part that connects the round ball tank to the regulator.