228 Slant
- New!
Ventilator 339, Used - F150
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
Valve Wheel Screw - S60
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
Valve Stem - E1228
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
- Free Shipping
Tip Cleaning, Needle Tool - S131
Reproduction tip cleaning tool for cleaning the gas tips on your Q99 or Q77 generator.
- New!
Slant Burner Top Half, Used - E1144
Used top half of the burner assembly for a slant lantern or lamp.
Q77 Steel Generator, Rusty, NOS - E1053
Interchangeable with the Q99 or R55 generator. Fits the model 327, 427 and Slant 220 lanterns. NOS - This does not come in original packaging and they are rusty on the outside. They are made of steel.
Q77 Generator Nut - S166
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
Pump Assembly, Universal - C045
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
Pump Assembly, 220C Thick Steel Cap, Used - E1296
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
- New!
Pump Assembly, 220B Thin Brass Cap, Used - E1054
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
Plastic Funnel Small - R702
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
N.O.S Burner Cap 220 Steel Hex - E1663
N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
- New!
Mica Globe w/Reflector - G10
For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.
These made in the USA Mica Globes measure 4 7/8" x 5 1/4" and fit 206, 220, 228, 231, 236, 237, 290, 295, and QuickLite lanterns.
Mica Globe Panels - E1120
These mica panels are 3" x 5" in size.
General information:
- Mica can be cut with sharp scissors or a good paper cutter
- This is the only size that is available
- Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
- Mica is not available in amber or red.
- Mica can withstand temperatures up to 1800 degrees F.
- These are only sold in a package of 5 panels.
Metal Funnel Small - R503
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Leather Pump Cup - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - S81
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Globe 220 White Logo USA Replacement - G127
Made in USA 220 white logo replacement.
This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Globe 220 Red Sunrise - G23
Used red sunrise globe used on Canadian lanterns. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Generator AGM Kamplite LRL21 - R400
Reproduction generator for the AGM model LRL21, LRL21A, LRL22, KL2, and JC Higgins model 710.7400, 710.74001 lanterns. Part number on JC Higgins parts diagram is 7110 - Generator Assembly
- New!
GPA Starter Toolbox Kit - K22
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
- 4 new Coleman check valves
- 10 Leather pump cups - pre-oiled
- 5 Neoprene rubber pump cups
- 10 Large valve stem packings for 1/4"
- 5 Small valve stem packings for 3/16"
- 10 Generator tube packings
- 10 One-piece fuel cap gaskets
- 10 Three-piece fuel cap gaskets
- 10 Cap gaskets sized for the 242 or 500 stoves
- 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns
Fuel Tube Spring, Steel - R581
New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
Fuel Tube Spring - S26
Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".
Check Valve Old Style - R425
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
Burner Tube Short/Slant - S135
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
Burner Cap 220 Steel Hex - E1267
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Burner Cap 220 Brass Round, NOS - E1044
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
Burner Cap 220 Brass Hex - S32
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
Ball Nut, Used - S101
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Bail Wrap Protector Clear - R512
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Bail Wrap Protector Black - R513
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Air Stem, Old Style, Long, Reproduction - R582
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Air Stem Old Style Long Used - E1613
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Air Stem Long New Style - E1048
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
- Free Shipping
427 Cap Gasket - S54
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
327 Mica Globe - G09
This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
- New!
228 Vent, Old Style Used - U867
This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)
228 Vent, Old Style Used - U866
This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).
228 Vent, Old Style Used - U865
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
220 White Logo USA Globe - G44
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 Red Logo Pyrex Globe USA - G28
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
220 Peerless Globe - G130
This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
220 No Letter Globe - G179
Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.