247
- Free Shipping
Filler Cap Gasket 242 size - S45
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
Pump Screw, Reproduction - R504
Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.
Burner Tube, Brass, NOS - E1269
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
- New!
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Burner Tube with Nut - Steel - E1127
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
Burner Tube Steel - E1357
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
Gas Bottle, 8 oz. - R321
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
Burner Cap Reproduction - S34
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
Burner Cap - 200/242 - C009
This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242 and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.Eccentric Block - S28
Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.
Ball Nut 242 Canadian, Wrench Marks - E1393
Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.
They will all show varying signs of wear/ wrench marks.
Alcohol Bottle, 2 oz. - C020
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Alcohol Bottle 8 oz. - R323
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Reproduction Canadian Ball Nut 242 - R575
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.
Ball Nut 242 Reproduction - R419
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
Bail Reproduction Bent - B100
Reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Looks identical to the original.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.
Pre-Heater Cup 234 Used - E1385
Original used pre-heater cup for the model 234 lantern. Also would be correct for the Canadian model 247 lantern.
Pre-Heater Cup, Small - C016
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".
242 Vent Rod, Reproduction - S145
Reproduction nickel plated vent rod for the models 234, 242A, 242B, 242C, 247, 249, and similar style lanterns. Will not fit the Australian made 249 lantern.
- Free Shipping
Filler Cap Gasket - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - S45
This is a 10 PACK of gaskets for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
242 Bail Used - E1531
This is a used bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Will show wear and rust and such, but be solid.
Check Valve With Stem - C001
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
Ball Nut, USA Style, Used - E1617
This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.
Ball Nut 242 Canadian, Used - E1211
Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.
They will all show varying signs of wear.
Globe 288 Clear - G03
It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
Also known as part numbers 2000038026 & R214D046C.
Bail Reproduction - R309
This is a very nice reproduction bail handle for models 242, 242A, 242B, 242C, 242K, 247, 249, 243, 243A, 243B, 234 and others. Made of spring steel here in the USA.
200A Globe Clear - G01
New Coleman made Globe. It will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
Also known as part number R690B051.
242 Burner Frame, Used - BF504
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
Is stamped with 3000.
Generator for 201/241/247 - C022
New Generator for 201, 241 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 242K289, 201B5891 and 3000005402.Mica Globe Panels - E1120
These mica panels are 3" x 5" in size.
General information:
- Mica can be cut with sharp scissors or a good paper cutter
- This is the only size that is available
- Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
- Mica is not available in amber or red.
- Mica can withstand temperatures up to 1800 degrees F.
- These are only sold in a package of 5 panels.
242 Burner Frame, Used - BF503
This is a used Burner frame for the 242A through C lantern. Will also work on the 247.
Is stamped with 3000.
- New!
440 Mica Globe w/Reflector - G11
For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.
These made in the USA Mica Globes measure 4 1/2" x 3 1/2" and fit the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns.
242 Filler Cap Brass, Used - E1049
Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Will come with a new gasket for you to install if needed.
Pump 242B Steel, Used - E1014
Used steel pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. Has the double screw holes on the plunger cap.
242 Pump Assembly, Used - E1589
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the single screw hole on the plunger cap.
242 Pump Assembly, Used - E1606
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the double screw holes on the plunger cap.
Globe Straight No Logo - G87
This is a used unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is a Fred Kuntz reproduction. Glass measures 3 1/2" Wide X 4" Tall.
- New!
Large Valve Stem Packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞- P01
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Filler Cap 242 Nickle Plated, Used - E1630
This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Comes with a new gasket for you to installed if needed.
242 Fount, 4-47, Used - F154
This is a used fount for the model 242 Lantern. It is date stamped 4-47. Has some paint chipping and a couple very small dents. The sunshine logo looks faded but is there.
It will work for models 242, 242A, 242B, 242C, 243, 243A, 247, and 242K.
247 Valve Assembly, Used - E1674
Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel.
We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
A graphite valve stem packing is included with each of these in case you end up needing to change them.
Fount 242, 9-47, Used - F157
This is a used brass nickel plated fount for the model 242C. It is date stamped 9-47. It will also work for models 242, 242A, 242B, 243, 243A, 247, and 242K. Has a small dent but otherwise in very nice condition - still has most of the nickel plating finish (see photos)
440 Mica Globe - G12
This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
- New!
Kamplite-AGM Globe - G209
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
200A Trailblazer Red Logo Globe - G32
This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.