442

Used valve wheel screw.  Will be in good condition. These will not fit the 236 or 237.

Fuel Air Tube for the 413 series and 442 series 2 burner stoves. NOS.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.

It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole. 

Old part number 115-1361. 

This will not seal they typical Coleman lantern cap.

Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.

Generator Coil. Rusty. 

Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.

Pump Clip

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

Lighting stem.

Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.

Block and Needle Assembly. Measures approximately 4 1/4 inches long.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

NOS Generator Coil. 

Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.

 O-Ring sizes are #6, #7, and #9, made of Flourosilicone.

We know it does work on these models: 533, 440, 442

Does not work on the 400B, 508B, 533A, 3024

This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203

Used valve Stem for the 413E, 413F, 413G, 413H, 425F, 425G, 426D, 442, 442A stoves. Also fits Sears stove models 476.72302, 476.72303, 47.74970 & 476.74980.  

You will need a P01 graphite packing for these which is HERE. Measurements:  just over 1-3/4" long and 1/4" diameter.

Please read this if you have a 425F: This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem and make sure it is 1/4".

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

Manifold pipe. It is 10 inches long.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.

This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443  Instant Light, 2 & 3 Burner Stoves

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one. 

 If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

This decal is for the Coleman Model 413G stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions.

This decal is for the Coleman Model 426C stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions.

This decal is for the Coleman Model 426C stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions.  The 426D came with 3 different decals through the years - this is version 1.

This decal is for the Coleman Model 426C stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions. The 426D came with 3 different decals through the years - this is version 2.