442
Valve Wheel Red, Used - E1151
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
Valve Wheel Red, Old Style, NOS - E1401
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
Valve Wheel Red Old Style, Used - S111
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
Valve Wheel Red New Style, Used - S114
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
Valve Wheel Black, Old Style, NOS - E1679
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
Valve Stem, Used - E1289
Used valve Stem for the 413E, 413F, 413G, 413H, 425F, 425G, 426D, 442, 442A stoves. Also fits Sears stove models 476.72302, 476.72303, 47.74970 & 476.74980.
You will need a P01 graphite packing for these which is HERE. Measurements: just over 1-3/4" long and 1/4" diameter.
Please read this if you have a 425F: This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem and make sure it is 1/4".
Valve Stem, NOS - E1252
Valve stem only. Fits the 413E, 413F, 413G, 413H, 425F, 426E, 442, 442A, Sears Models 476.72303, 476.74980, 476.72302, and 476.74970. Comes with a new packing installed. Also known as part number 413A2521.
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Valve Assembly Small Stem - E1292
Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.
Valve & Generator - C033
New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980
- Free Shipping
Stove Lid Decal, 426D Version 3 - D163
This decal is for the Coleman Model 426C stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions. The 426D came with 3 different decals through the years - this is version 3.
- Free Shipping
Stove Lid Decal, 426D Version 2 - D162
This decal is for the Coleman Model 426C stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions. The 426D came with 3 different decals through the years - this is version 2.
- Free Shipping
Stove Lid Decal, 426D Version 1 - D161
This decal is for the Coleman Model 426C stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions. The 426D came with 3 different decals through the years - this is version 1.
- Free Shipping
Stove Lid Decal, 426C - D160
This decal is for the Coleman Model 426C stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions.
- Free Shipping
Stove Lid Decal, 413G - D157
This decal is for the Coleman Model 413G stove. It calls out the 413A5621 generator which is also used on models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. We placed this on a black background so you can read the text. Very nice decal with proper dimensions.
Stove Generator- 400B/440/442/508A/508B/533 - C013
This is a new generator that fits stove models 400B, 440, 442, 508A, 508B, 533, and 533A.
Also known as part numbers 3000005101, and 442-5891
Short Pump Plunger, Plastic Cap - C037
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
- Free Shipping
Pump Clip, Used - S100
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
- Free Shipping
Plastic Funnel Small - R702
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
- Free Shipping
O-Ring Set Canadian Blue - K12
Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.
O-Ring sizes are #6, #7, and #9, made of Flourosilicone.
We know it does work on these models: 533, 440, 442
Does not work on the 400B, 508B, 533A, 3024
Metal Funnel Small - R503
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Leather Pump Cup - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - S81
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Large Valve Stem Packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞- P01
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- New!
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Generator Stove, NOS - E1466
Used generator for the model 413E and 443 stoves according to early part diagrams.
I believe it is the same generator as part number 413A5621.
This is the earlier style with the square soldered on nut which does make it easier to install. Comes with tip needle, coil and housing. This one is in good shape.
Generator Stove - C030
Fits models 413E, 413F, 413G, 426B, 426C, 426D, 442, 442A, and 443. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005106.
Generator Coil, NOS - E1124
NOS Generator Coil.
Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.
Generator Coil - E1345
Generator Coil. Rusty.
Fits 426B, 426C, 413E, 413F, 413G, 442, 442A and 443 stoves.
Gas Bottle, 8 oz. - R321
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
- New!
GPA Starter Toolbox Kit - K22
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
- 4 new Coleman check valves
- 10 Leather pump cups - pre-oiled
- 5 Neoprene rubber pump cups
- 10 Large valve stem packings for 1/4"
- 5 Small valve stem packings for 3/16"
- 10 Generator tube packings
- 10 One-piece fuel cap gaskets
- 10 Three-piece fuel cap gaskets
- 10 Cap gaskets sized for the 242 or 500 stoves
- 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns
Filler Cap, Tire Valve, Brass - R302
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Filler Cap, Burgundy - E1570
This is a used one piece filler cap off the Model 200A burgundy.
Comes with a new gasket that you will have to install.
Filler Cap, Brass - C004
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
Filler Cap, Black, Used - E1041
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Filler Cap, Assorted, Used - E1114
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Filler Cap Tire Valve Nickel - R301
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
Filler Cap Steel, Used - E1386
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Filler Cap Red Used - U801
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Filler Cap Nickel, Used - E1597
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
Filler Cap Nickel, Used - E1395
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
Filler Cap Insert, Reproduction - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Filler Cap Green Used - U803
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.