M1942
Vaporizer Screen - S159
Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
Vaporizer 520 - E1464
For the model 520 stove. New generator includes new gas tip and tip cleaning wire. LINK for great info on these and what they fit.
Additional info: The 520 (aka M1941) and M1942 generators are usually interchangeable. The only exception is the early version of the M1942, known as the Mountaineer Stove. It has a vertical sprocket-type valve wheel. The generator on that stove seems to be unique in that it's a bit shorter than the later version.
Valve Stem Retaining Ring - 1/4" - S04
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Valve Stem Nut - S152
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Small Pump Leather - S83
Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.
- 73% less
Parts Tube - E1418
Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.
Military Funnel Chain - E1643
Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.
NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit. No other sizes of chain are currently available that are an exact match to what was used.
M1942 Wood Knob - S58
Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.
M1942 Pump Rebuild Kit - K06
This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.
- Free Shipping
M1942 Preway Decal - D75
Decal for the Preway made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
M1942 Pip Spring - S173
This is the spring used in the non return valve located in the bottom of the M1942 pump. Reproduction part.
- Free Shipping
M1942 Coleman Decal - D77
Decal for the Coleman made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
- Free Shipping
M1942 Aladdin Decal - D74
Decal for the Aladdin made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
M-1942 Mod Tip Cleaner Packing - S171
M-1942 Mod Tip Cleaner Graphite packing for all companies who manufactured the stove.
Large Valve Stem Packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞- P01
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- New!
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
- Free Shipping
- Free Shipping
520/M1941 Parts Tube - E1244
Parts tube for the M1941, M1942, 520 and 523 military stoves. Each contains a new vaporizer, gas tip, large packing, and 3 screens. LINK for great info on these and what they fit.