530 Pocket Stove

Used case for a 530 stove. Has wear from age and use but still in good condition.
The 530's were made from 1946-1950 for both the U.S. and the Canadian market.
Originally these were called the "G.I. Pocket Stove" because the G.I.'s returning home enjoyed using the 520 stove made for the military. 

New old stock filler cap and chain for the military lantern. Will also fit any Coleman lantern or stove that used the standard size filler cap. I am 99% sure these filler caps came from the old SMP factory.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

New reproduction generator (also called a vaporizer). Includes new gas tip, screen, and tip cleaning wire. Fits the model 530 pocket stove.

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Wear and finish will vary. 

Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Used top half of a 530 stove. Missing all of burner supports.

Used top half of a 530 stove - Comes with burner supports.

Rebuild kit for the 530 Pocket Stove. Includes a new reproduction generator (also called a vaporizer), valve stem packing, new leather pump cup, and a fuel cap gasket.

If you need other parts for the 530 stove, click HERE.

This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

Reproduction wrench for the 530 pocket stove.

Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.

Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.

This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.

Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.

Looks like it may have gotten a little too hot and burned (see photos)

Used pump for the model 530 stove. Will have a new pump leather and work just fine.

Used 530 valve with vaporizer

Air stem for the 530 stove.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

This is a reproduction flame diffuser plate for the 520 and 530 stoves. These are very nice plates. Professionally cut. 4 inch diameter.

Stainless steel diffuser plate for the model 530 stove. 4 inch diameter. Professionally cut.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.

NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit.  No other sizes of chain are currently available that are an exact match to what was used.

Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".

Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.

Fits the cap number: 220C1401

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

Pre-heater cup for the model 237 lantern. This is a new production cup made out of brass. It is very high quality and fits the 237 nice and snug. Will also fit a 530 stove if you want to install a PH cup on it.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.