Search

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

NOS Valve for tanks 457, 465, and 653D.

NOS valve assembly for the model 201 kerosene lantern.

This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.

C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

Control Valve & Generator Assembly Complete 414/428

New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980

New Coleman made valve and generator. This part will fit: 2G, 2H, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 421, 421C, 421D, 421E, 425, 425B, 425C, 425D, 425E, 425F and Sears 476.72301, 476.74960, and 476.72244.

New old stock valve assembly for the QuickLite model 327 lantern.

Valve and Generator. Fits the model 413H and 426E stove.

Valve stem for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.

NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

Valve body assembly that fits 5410A700, 5410A708, and 5410B708

Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel. 

We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

A graphite valve stem packing is included with each of these in case you end up needing to change them.

Valve minus the generator for the model 425 series stoves.

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

New valve stem packing has been installed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

N.O.S Valve stem for the model 335 and 339 lanterns.

Has a small chip on the valve wheel.

Lamp valve for 130G, 130K 130P and 131P.  The bottom is threaded for a fuel and air tube to be attached.

Don't know the part number for this valve and generator. It measures 10 1/4 inches long from tip to end of nut. 

Used Fuel Valve Assembly

NOS valve minus the generator and valve wheel, for the model 425 series stoves. 

This is a new old stock pre-heater valve for the M2 military stove.

Rebuild kit for the 500 & 500A stove. Kit includes a new reproduction generator, valve stem packing, leather pump cup, and a new fuel cap gasket (stove came with one of two types - each is included).

If you need other parts for your stove, click HERE.

Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.

Rebuild kit for 502 Sportster Stove. Cures most troubles.

Includes:

• 1 Reproduction Generator for the 502 stove lanterns
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in Below

More parts for the 502 Stove HERE. 

Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.

This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.

Valve assembly for the 400B, 3024, 442  and 440 single burner stoves.

Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.

Includes:

• 4 Coleman string tie mantles for the 200 or 200A lantern
• 1 Reproduction Generator for the 200 or 200A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 200 HERE
• 200A HERE

Valve and generator.

This is a new old stock pre-heater valve for the M2 military stove. Does not have the valve stem or wheel (knob). 

Rebuild kit for both the 200 and 200A lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 200 or 200A lantern
• 1 Reproduction Generator for the 200 or 200A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 200 HERE
• 200A HERE

Used 530 valve with vaporizer

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Rebuild kit for both the 220 and 228 Coleman lanterns. Cures most troubles.

Includes:

• 4 Peerless mantles for your lantern
• 1 Reproduction generator
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 2 Cap Gaskets - for the bottom of your fuel cap. 1 each of the two possible types needed

See Diagram in "Description" under photo at bottom left of this page

Rebuild kit for both the 275 and 275A lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 275 or 275A lantern
• 1 Reproduction Generator for the 275 or 275A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 1 Cap Gasket - for your fuel cap.

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 275 HERE
• 275A HERE

Rebuild kit for models 242, 242A, 242B, and the 242C lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 242 lanterns
• 1 Generator for the 242 lanterns
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 1 Cap Gasket specific to the 242 - for the bottom of your fuel cap.

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 242 HERE
• 242A HERE
• 242B HERE
• 242C HERE

New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.

Used valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.

Used 242 Valve stem.

Packings have not been changed, if you need one they are HERE

Valve assembly Fits 508A, 508B, 533 and the 533A

This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Valve Assembly for the 285 lantern.

Valve Assembly 295 Lantern

New NOS valve stem for the model 200A lantern.

This is a Coleman made new valve assembly that fits the 290 and 290A model lanterns. These have a metal eccentric block, feed tube, new knob and screw included.

Valve assembly for Northstar Lantern.

This is a new Coleman made valve assembly. Includes the valve, knob w/screw, fuel pick up tube and eccentric block. Fits both the 288 and 288A lanterns.

Valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.